Homework Answers
Add Answer to:
Question 3 Design a thick-walled metallic cylinder of a 200 mm internal diameter for an internal...
with steps please!!! Question3 Design a thick-walled metallic cylinder of a 200 mm internal diameter for an internal...
with steps please!!!
Question3 Design a thick-walled metallic cylinder of a 200 mm internal diameter for an internal pressure of 30 MPa such as to provide a factor of safety of 3.0 against any yielding in the cylinder and a factor of safety of 4.0 against ultimate collapse. The yield stress of the material is 480 MPa Use both linear and non-linear stress distribution methods of calculation. Compare and discuss the results.
Question3 Design a thick-walled metallic cylinder of a...
A thick-walled steel cylinder with internal diameter = 16 mm and external diameter = 24 mm is sub...
A thick-walled steel cylinder with internal diameter = 16 mm and
external diameter = 24 mm is subjected to a gradually increasing
internal pressure P.
I. Using accurate formulation, determine the value
of P and sketch the distribution of radial, tangential and maximum
shear stresses when:
a. The material of the cylinder first commences to
yield.
b. Yielding progressed to mid-depth of the cylinder
wall (at D= 20 mm ).
c. The material of the cylinder suffers complete
collapse (fully...
with steps please Question4 A thick-walled cylinder of mild steel with internal diameter of 80 mm and external diame...
with steps please
Question4 A thick-walled cylinder of mild steel with internal diameter of 80 mm and external diameter of 120 mm is loaded by internal pressure. The yield strength of the material is 300 MPa. a. Find the internal pressure required to initiate yielding in the cylinder using Lame's formulation. Sketch the stress distribution giving significant stress values. b. Find the plastic limit pressure at which the cylinder is fully plastic using non-linear formulation. Sketch the stress distribution giving...
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yie...
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yield stress of 240 MPa. +F 200 mm Fig. Q5 (a) If a tensile axial force of 1MN is applied to the end plate, show that the maximum internal pressure that can be applied before the cylinder yields according to the Tresca criterion is 16.2...
Problem 1 A thin-walled pressure vessel of mean radius R 100 mm and thickness t (R) is subjected to cyclic internal pressure p in the range -3 MPa p7 MPa. Using Soderberg's relation with maxim...
Problem 1 A thin-walled pressure vessel of mean radius R 100 mm and thickness t (R) is subjected to cyclic internal pressure p in the range -3 MPa p7 MPa. Using Soderberg's relation with maximum distortional strain energy theory, and safety factor of 2.6 determine the number of cycles to failure ift-5 mm Assume ơy(yield stress)-350 MPa, NY (Number of cycles to yield)-10, ơ (endurance stress)-290 MPa, Ne (number ofcycles associated with endurance stress)-10
Problem 1 A thin-walled pressure vessel...
UESTION # 2: (20 Marks) The thick cylinder shown in Fig. Q2(a) is made of high strength steel wit...
UESTION # 2: (20 Marks) The thick cylinder shown in Fig. Q2(a) is made of high strength steel with an internal diameter of 200 mm and an external diameter of 300 mm. It is subjected to an internal pressure P 60 MPa The cylinder is assumed to have closed ends, as depicted in Fig. Q2(b) (a) Determine the stress state acting on the element abcd located on the outer surface of the cylinder as a result of Pi; see Fig....
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power a...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
Problem 1: (a)A thick-walled cylinder, made from a homogeneous and isotropic elastic material, has an inner...
Problem 1: (a)A thick-walled cylinder, made from a homogeneous and isotropic elastic material, has an inner radius a and outer radius b. The cylinder is subjected to an internal pressure pi, and is under plane stress conditions. In this case the displacement field is of interest is given by and the stress field of interest is given by C2 C2 where, with (E and v) denoting the Young's modulus and the Poisson's Ratio. EA EB Show that b2 b2 (b/a)2-1)...
1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins...
1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that ink BD is not reinforced around the pin holes Front view 18 mm Side...
A3. A pressurized cylinder has an internal diameter of 80mm and a wall thickness of 3mm....
A3. A pressurized cylinder has an internal diameter of 80mm and a wall thickness of 3mm. If the yield stress of the materials is 250 MN/m' and the factor of safety is 2.5. determine the maximum internal pressure within the design limit. (8 marks)
with steps please!!!
Question3 Design a thick-walled metallic cylinder of a 200 mm internal diameter for an internal pressure of 30 MPa such as to provide a factor of safety of 3.0 against any yielding in the cylinder and a factor of safety of 4.0 against ultimate collapse. The yield stress of the material is 480 MPa Use both linear and non-linear stress distribution methods of calculation. Compare and discuss the results.
Question3 Design a thick-walled metallic cylinder of a...
A thick-walled steel cylinder with internal diameter = 16 mm and
external diameter = 24 mm is subjected to a gradually increasing
internal pressure P.
I. Using accurate formulation, determine the value
of P and sketch the distribution of radial, tangential and maximum
shear stresses when:
a. The material of the cylinder first commences to
yield.
b. Yielding progressed to mid-depth of the cylinder
wall (at D= 20 mm ).
c. The material of the cylinder suffers complete
collapse (fully...
with steps please
Question4 A thick-walled cylinder of mild steel with internal diameter of 80 mm and external diameter of 120 mm is loaded by internal pressure. The yield strength of the material is 300 MPa. a. Find the internal pressure required to initiate yielding in the cylinder using Lame's formulation. Sketch the stress distribution giving significant stress values. b. Find the plastic limit pressure at which the cylinder is fully plastic using non-linear formulation. Sketch the stress distribution giving...
MEE2001/2015 Q5. A thin walled steel cylinder with 10 mm wall thickness and internal diameter of 200 mm (Fig. Q5) is subjected to an internal pressure, p. The steel used for the cylinder has a yield stress of 240 MPa. +F 200 mm Fig. Q5 (a) If a tensile axial force of 1MN is applied to the end plate, show that the maximum internal pressure that can be applied before the cylinder yields according to the Tresca criterion is 16.2...
Problem 1 A thin-walled pressure vessel of mean radius R 100 mm and thickness t (R) is subjected to cyclic internal pressure p in the range -3 MPa p7 MPa. Using Soderberg's relation with maximum distortional strain energy theory, and safety factor of 2.6 determine the number of cycles to failure ift-5 mm Assume ơy(yield stress)-350 MPa, NY (Number of cycles to yield)-10, ơ (endurance stress)-290 MPa, Ne (number ofcycles associated with endurance stress)-10
Problem 1 A thin-walled pressure vessel...
UESTION # 2: (20 Marks) The thick cylinder shown in Fig. Q2(a) is made of high strength steel with an internal diameter of 200 mm and an external diameter of 300 mm. It is subjected to an internal pressure P 60 MPa The cylinder is assumed to have closed ends, as depicted in Fig. Q2(b) (a) Determine the stress state acting on the element abcd located on the outer surface of the cylinder as a result of Pi; see Fig....
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
Problem 1: (a)A thick-walled cylinder, made from a homogeneous and isotropic elastic material, has an inner radius a and outer radius b. The cylinder is subjected to an internal pressure pi, and is under plane stress conditions. In this case the displacement field is of interest is given by and the stress field of interest is given by C2 C2 where, with (E and v) denoting the Young's modulus and the Poisson's Ratio. EA EB Show that b2 b2 (b/a)2-1)...
1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that ink BD is not reinforced around the pin holes Front view 18 mm Side...
A3. A pressurized cylinder has an internal diameter of 80mm and a wall thickness of 3mm. If the yield stress of the materials is 250 MN/m' and the factor of safety is 2.5. determine the maximum internal pressure within the design limit. (8 marks)
Most questions answered within 3 hours.
-
Minitab Problem: Take the Lake Hume June rainfall data and find
use the processes outlined in...
asked 7 minutes ago -
X Company is trying to decide whether to continue using old
equipment to make Product A...
asked 8 minutes ago -
IN PYTHON ONLY !! Program 2: Re-work
program #5 (WeeklyHours) from the previous assignment such that...
asked 45 minutes ago -
The average length of time between arrivals at a turnpike
toll-booth is 26 seconds. What is...
asked 2 hours ago -
(a) A piston at 6.1 atm contains a gas that occupies a volume of
3.5 L....
asked 3 hours ago -
Please answer true or false. Words
cannot be changed or added in to make it true...
asked 3 hours ago -
An empty test tube weighs 15.923 grams. Then,
MgCl2•6H2O is added into the test tube. After...
asked 3 hours ago -
Assume memory access is 10 units of time and disk access is
10000 units of time....
asked 3 hours ago -
1. Are all good samples random?
2. Magazines often report surveys giving statistics such as “63%...
asked 4 hours ago -
Under all the various types of market structures, firms
must eventually earn some economic profits for...
asked 4 hours ago -
Consider the following fitness regime for a single locus trait
with two co-dominant alleles: w11 =...
asked 4 hours ago -
A large cable company reports the following.
80% of its customers subscribe to its cable TV...
asked 4 hours ago