P6.074 The torsional assembly consists of a cold-rolled stainless steel tube connected to a solid cold-rolled...
The torsional assembly in the Figure above consists of a cold-rolled stainless-steel tube AC with an outside diameter of 4 in., a wall thickness of 0.2 in., a shear modulus of G = 12,500 ksi, and an allowable shear stress of 35 ksi. The tube AC is connected to a solid cold-rolled brass segment CD at the flange C and has a diameter of 2.50 in., a shear modulus of G = 5,600 ksi, and an allowable shear stress of...
P6.041 A solid 66-mm-diameter cold-rolled brass G = 40.8 GPa) shaft that is 1.22 m long extends through and is completely bonded to a hollow aluminum LG = 27.5 GPa) tube. Aluminum tube (1) has an outside diameter of 89 mm, an inside diameter of 66 mm, and a length of 0.64 m. Both the brass shaft and the aluminum tube are securely attached to the wall support at A. Assume L1=L2 = 0.64 m, L3= 0.58 m, To =...
A solid 70-mm-diameter cold-rolled brass [G = 38.4 GPa] shaft that is 1.13 m long extends through and is completely bonded to a hollow aluminum [G = 25.6 GPa] tube. Aluminum tube (1) has an outside diameter of 98 mm, an inside diameter of 70 mm, and a length of 0.73 m. Both the brass shaft and the aluminum tube are securely attached to the wall support at A. Assume L1=0.73 m, L2=0.4 m, TB=25 kN-m, and TC=7 kN-m. When...
P6.042 The composite shaft shown in the figure consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 173 mm and a wall thickness of 6 mm. Steel pipe (2) has an outside diameter of 101 mm and a wall thickness of 7 mm. Both pipes are 3.4 m long and have a shear modulus of 80 GPa. If a concentrated...
A solid steel bar of circular cross section has diameter d = 40 mm, length L = 1.3 m and shear modulus of elasticity G = 80 GPa. The bar is subjected to torques T acting at the ends. If the torques have magnitude T = 340 Nm, what is the maximum shear stress in the bar? What is the angle of twist between the ends? If the allowable shear stress is 42 MPa and the allowable angle of twist...
Problem 10.2: (P15.47 from Text) The piping assembly shown below consists of stainless steel pipe that has an outside diameter of 6.675 in. and a wall thickness of 0.28 in. The assembly is subjected to concentrated loads Px = 320 lb, Py = 410 lb, and Pa = 180 lb as well as an internal fluid pressure of 100 psi that acts in all pipes. Dimensions of the assembly are yı = 2.0 ft, y2 = 4.5 ft, Z1 =...
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2 in., respectively, is turning at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524 N-m from the engine...
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2 in., respectively, is turning at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524 N·m from the engine...
Mechanics and Materials Help Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2 in., respectively, is tuming at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524...
Both parts please Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in and 2 in., respectively, is turning at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T-524 N-m from the...