Due 10/31/2019 A ductile steel has a yield strength of 40 ksi. Find the factor of...
A) A ductile hot-rolled steel bar has yield strength in tension and compression of 400 MPa Define Maximum shear stress, and Maximum normal stress for the following stress distribution: ?,-200 Mpa and ?,-200 Mpa, and Txysl 00 Mpa (All the other stresses are set to zero). safety factor using distortion energy theory, Maximum Normal stress theory, and maximum shear stress theory B) For the above material and stress distribution, what is the
1. A ductile hot rolled steel bar has minimum yield strength of 360 MPa. Using the distortion-energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states: (20 points) (a) Ox = 200 MPa, y = 120 MPa (b) x = 180 MPa, Txy = 150 MPa (c) Txy = 100 MPa
step by step please.
A ductile hot rolled steel bar has minimum yield strength of 360 MPa. Using the distortion-energy and maximum-shear-stress theories, determine the factors of safety for the following plane stress states: (20 points) (a) 0x = 200 MPa, y = 120 MPa (b) x = 180 MPa, Txy = 150 MPa (c) Txy = 100 MPa
A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syt = 60 kpsi and Syc = 75 kpsi. Using the ductile Coulomb-Mohr theory, determine the factor of safety for the states of plane stress. 0x = -21.8 kpsi, oy" -21.8 kpsi, and Txy=-16 kpsi The factor of safety is 2.455
Determine the required diameter of a steel transmission shaft 10 m in length and of yield strength 350 MPa in order to resist a torque of up to 500 N-m. The shaft is supported by frictionless bearings at its ends. Design the shaft with a factor of safety of 1.5 according to (a) the maximum shear stress theory and (b) the maximum distortion energy theory
Problem 10.81 The material shown in the figure below (Figure 1) has a yield strength of Oy = 80 ksi. Figure < 1 of 1 > 12 ksi 10 ksi -20 ksi Part A Determine the factor of safety for this loading against yielding based on the maximum shear stress theory. Express your answer to three significant figures. Y A vec mo? F.S. Submit Request Answer Part B Determine the factor of safety for this loading against yielding based on...
An AISI steel has a yield strength, Sy = 300 Mpa. Plot the failure locus and the load line in the attached diagram. Given that - OA Ox = 210 MPa, Oy = 160 MPa, and Txy -45 MPa Distortion Energy (Von Mise) S Hint: Maximum Shear Stress Oxt Oy OB ОА, Ов + + tzy Failure Theory Diagram 1.jpg Instructions: Download the image (Failure Theory Diagram 1.jpg), complete the d
True or False 1. For a fatigue failure, a part always fails above the ultimate strength of the material. 2. For a ductile material, the tensile yield strength and the compressive yield strength are not equal 3. Mode I of crack propagation occurs due to compressive stress 4. Distortion energy theory is used to predict failure for brittle materials 5. Temperature does not affect the endurance limit of a material 6. For a fatigue failure, a part always fails above...
Stress Analysis
3. A 20-mm diameter rod made ofa ductile material with a yield strength of 350 MPa is subjected to torque of 100 N.m and a bending moment of 150 N.m. An axial force is then gradually applied. Determine the value of force when the rod begins to yield. Solve the problem two ways using the (a) Tresca theory (Maximum shearing stress theory) and (b) von Mises theory (Maximum distortion energy theory) [12+12 points
3. A 20-mm diameter rod...
a cylindrical tank is made from A-36
OBLEM 2: The cylindrical tank is made from A-36 steel with a yield strength ayie 250 MPa, modulus ef elasticity &-200 GPa and Poisson's ratio v 0.3. When the tank is pressuri pressure p, a 60 strain rosette mounted on the surface measures the following strains: & 100(10), 343(10), maximum-distortion-energy theory, to determine the factor of safety against yielding (c) Find the internal pressure p acting within the tank. (30 Points) 343(10) Use...