Homework Answers
Add Answer to:
Review ▼ Part A The propeller shaft of the tugboat is subjected to the compressive force...
3. The propeller shaft of the tugboat is subjected to the compressive force and torque shown....
3. The propeller shaft of the tugboat is subjected to the compressive force and torque shown. The shaft has an inner diameter of 125 mm and an outer diameter of 175 mm. (20 pts) 0410 KN 2 kNm Determine the following at point A located on the outer surface: avg. TMIP, 8s Principal stresses and Op c Draw Mohr's circle d Draw principal stress and maximum in plane shear stress elements
Please answer the following question clearly. Question Part A The steel pipe is filled with ooncrete...
Please answer the following question
clearly.
Question Part A The steel pipe is filled with ooncrete and subjected to a compressive force outer diameter of 80 mm and an inner diameter of 60 mm. E 200 GPa, Ee al stress in the concrete and the steel due to this loading. The pipe has an 24 GPa (Figure 1) Enter your answers, separated by a comma MPa Figure 1 of 1 Submit 80 kN Provide Feedback Next > 500 mm
st QUESTION 3 A hollow shaft is subjected to a twisting moment of 200 N.m and...
st QUESTION 3 A hollow shaft is subjected to a twisting moment of 200 N.m and a bending moment of 80 Nm. Determine the outer diameter of the shaft (mm) according to the maximum shear stress theory, if the allowable shear stress is 40 MPa ? The outer diameter of the shaft is twice the inner diameter اللتي و Click Save and Submit to save and submit. Click Save All Answers to save all answers.
The splined ends and gears attached to the A992 steel shaft are subjected to the torques...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks) a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks] a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
A propeller steel shaft subjected to an axial load of 39,402 N, in addition to combined...
A propeller steel shaft subjected to an axial load of 39,402 N, in addition to combined torque and bending loads. The diameter of the shaft is 74 mm. The Bending Moment equal to 1,670 N.mm The Torsion Moment equal to 16000 N.mm Compute the Resultant stress for the shaft (N/mm2)? 10 points Save Answer
Part A The 56-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown,...
Part A The 56-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T-470 N-m(Figure 1) Determine the absolute minimum shear stress on the shall's surface, and specify its location, measured from the fixed end C Express your answers, separated by a comma, to three significant figures. VAE 11 vec o ? T min MPa.mn Submit Request Answer Figure 1 of 1 Part B 2 kN.m/m Determine the absolute maximum shear stress on the shaft's surface,...
Part A The wide-flange beam is subjected to the P 54 kN force. Determine the principal...
Part A The wide-flange beam is subjected to the P 54 kN force. Determine the principal stresses in the beam at point A located on the web at the bottom of the upper flange. Although it is not very accurate, use the shear formula to calculate the shear stress. (Figure 1) Determine the principal stress at point A Express your answer to three significant figures and include the appropriate units. MPa Figure 1 of 1 Request Answer Submit vious Answers...
P B A pressurized cylindrical air tank is subjected to a force P at a collar...
P B A pressurized cylindrical air tank is subjected to a force P at a collar B. The tank has an inner diameter (d = 160 mm) with wall thickness (1 = 6 mm). The gage pressure inside the tank is p = 5 MPa and the applied force is P = 9.5 kN. (a) Determine the maximum tensile stress o [MPa), maximum compressive stress oc [MPa] and maximum shear stress imax [MPa) at point a. (b) Repeat part (a)...
(50 Marks) a) As part of the product development process for go-kart drive shaft, the engineer has instrumented a critical area of the shaft with a solid bar. A drive shaft bar is designed to car...
(50 Marks) a) As part of the product development process for go-kart drive shaft, the engineer has instrumented a critical area of the shaft with a solid bar. A drive shaft bar is designed to carry a tensile load. The engineer has proposed a circular bar with cross-section having a radius of 2X mm. It carries an axial tensile load of İY0 kN. By using equation; i) Calculate the values of principal stresses at the critical area of the bar....
3. The propeller shaft of the tugboat is subjected to the compressive force and torque shown. The shaft has an inner diameter of 125 mm and an outer diameter of 175 mm. (20 pts) 0410 KN 2 kNm Determine the following at point A located on the outer surface: avg. TMIP, 8s Principal stresses and Op c Draw Mohr's circle d Draw principal stress and maximum in plane shear stress elements
Please answer the following question
clearly.
Question Part A The steel pipe is filled with ooncrete and subjected to a compressive force outer diameter of 80 mm and an inner diameter of 60 mm. E 200 GPa, Ee al stress in the concrete and the steel due to this loading. The pipe has an 24 GPa (Figure 1) Enter your answers, separated by a comma MPa Figure 1 of 1 Submit 80 kN Provide Feedback Next > 500 mm
st QUESTION 3 A hollow shaft is subjected to a twisting moment of 200 N.m and a bending moment of 80 Nm. Determine the outer diameter of the shaft (mm) according to the maximum shear stress theory, if the allowable shear stress is 40 MPa ? The outer diameter of the shaft is twice the inner diameter اللتي و Click Save and Submit to save and submit. Click Save All Answers to save all answers.
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks) a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks] a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
A propeller steel shaft subjected to an axial load of 39,402 N, in addition to combined torque and bending loads. The diameter of the shaft is 74 mm. The Bending Moment equal to 1,670 N.mm The Torsion Moment equal to 16000 N.mm Compute the Resultant stress for the shaft (N/mm2)? 10 points Save Answer
Part A The 56-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T-470 N-m(Figure 1) Determine the absolute minimum shear stress on the shall's surface, and specify its location, measured from the fixed end C Express your answers, separated by a comma, to three significant figures. VAE 11 vec o ? T min MPa.mn Submit Request Answer Figure 1 of 1 Part B 2 kN.m/m Determine the absolute maximum shear stress on the shaft's surface,...
Part A The wide-flange beam is subjected to the P 54 kN force. Determine the principal stresses in the beam at point A located on the web at the bottom of the upper flange. Although it is not very accurate, use the shear formula to calculate the shear stress. (Figure 1) Determine the principal stress at point A Express your answer to three significant figures and include the appropriate units. MPa Figure 1 of 1 Request Answer Submit vious Answers...
P B A pressurized cylindrical air tank is subjected to a force P at a collar B. The tank has an inner diameter (d = 160 mm) with wall thickness (1 = 6 mm). The gage pressure inside the tank is p = 5 MPa and the applied force is P = 9.5 kN. (a) Determine the maximum tensile stress o [MPa), maximum compressive stress oc [MPa] and maximum shear stress imax [MPa) at point a. (b) Repeat part (a)...
(50 Marks) a) As part of the product development process for go-kart drive shaft, the engineer has instrumented a critical area of the shaft with a solid bar. A drive shaft bar is designed to carry a tensile load. The engineer has proposed a circular bar with cross-section having a radius of 2X mm. It carries an axial tensile load of İY0 kN. By using equation; i) Calculate the values of principal stresses at the critical area of the bar....
Most questions answered within 3 hours.
-
Here is a pair of aromatic compounds that each have a complicated
set of aromatic peaks....
asked 8 minutes ago -
As with many public goods, determining the appropriate level of
government support for the production of...
asked 12 minutes ago -
Write a balanced chemical equation for the oxidation reaction
between Caro’s acid (H2SO5) and CN– ion...
asked 15 minutes ago -
Calculate the number of valence electrons for
[Mo(C6H6)(CO)3]
asked 25 minutes ago -
Which of the following are true about the strength of the
association between two variables?
1-...
asked 22 minutes ago -
You are a monopolist and know that your consumers have a linear
demand curve. At what...
asked 20 minutes ago -
Raising a heavy load requires work. Raising it in half the time
requires:
asked 27 minutes ago -
MGT-201: Marketing Management
Before deciding on the structure of the channel marketers must
take several factors...
asked 27 minutes ago -
1. ACLs allow a router to control traffic within a network. The
concept is very similar...
asked 28 minutes ago -
35. When the electron in a hydrogen atom falls from its first
excited energy level to...
asked 30 minutes ago -
A man is dragging a box of mass "m" by using a rope which rests
on...
asked 46 minutes ago -
Liquid octane
(CH3(CH2)6CH3) will
react with gaseous oxygen (O2) to produce gaseous carbon
dioxide (CO2) and...
asked 48 minutes ago