11. A vertical square hatch (3 ft by 3 ft) is located on the side of...
A 5-ft diameter 300-lb circular hatch is located on a submarine, as shown. The submarine is in sea water with a specific weight of 64 lb/ft3 . Determine the following: (a) the resultant force on the hatch due to the water pressure (b) the location of the resultant force (distance below the water surface). (c) the magnitude of the force, F, which should be applied to open the hatch when it is submerged as shown. It is hinged at the...
Question 19 4 pts Find the fluid force on the vertical side of the tank, where the dimensions are given in feet. Assume that the tank is full of water. Note: The density of water is 62.4 lbs per cubic foot. -5 3 2340 lb 468 lb 62.4 lb 249.6 lb 1404 lb
Just 1,2and3 Then, h is computed as follows. cos-=- 154.5 2.0-h 2.0 (Answer) h= 1.56 ft. PROBLEMS T What is the pressure at the bottom of Sunfish Pond, which has a depth of 350 feet? 2. A swimming pool has depths of 4.0 feet and 12.0 feet at the shallow and deep ends, respectively. Find the pressure in lb/ft2 at each end. 3. A reservoir of water is connected to a 12-inch-diameter pipe that is 50 feet long and capped...
Hydrostatic Pressure. A rectangular vertical plate is submerged in water. The top edge is horizontal and at a depth of 0.6m. The length of the vertical edge is 1.2m. determine at what dept under the water surface a horizontal line can be drawn on the plate such that the hydrostatic forces on either side of the line is equal. (Hint: The magnitude of the hydrostatic force on a vertical surface is equal to the average pressure x the area.Fluid Mechanics...
A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure below. The gate is hinged along its top edge and is held in position by the force P. Friction at the hinge and the weight of the gate can be neglected. Determine the required value of P. Water 29 ft Hinge Gate 60° lb A rectangular gate having a width of 4 ft is located in the...
Determine the force due to hydrostatic pressure on the flat vertical side of a tank which has the shape in feet of the boundaries y=0, y=3x−5, y=−3x−5 and the line y=22. Note that water has density 62.4lb/ft3. Determine the force due to hydrostatic pressure on the flat vertical side of a tank which has the shape in feet of the boundaries y = 0, y = 3x - 5, y = -3x -5 and the line y = 22. Note...
The figure shows a cylindrical tank of 80 em in diameter which is fully filled with water. In order to increase the flow from the tank to the exit pipe on the left, an additional pressure is applied to the water surface by an air compressor to supply air to the upper air chamber of the tank. The external walls of the tank are exposed to the atmospheric conditions of the area. You are required to determine the hydrostatic conditions...
2. A 5-ft square, 2-ft deep spread footing is subjected to a concentric vertical load of 60 k and an overturning moment of 30 ft-k. The overturning moment acts parallel to one of the sides of the footing, the top of the footing is flush with the ground surface, and the ground water table is at a depth of 20 ft below the ground surface. Compute the minimum and maximum bearing pressures, d show the distribution of bearing pressure in...
Water in a vertical cylindrical tank of height 29 it and radius 4 ft is to be pumped out. The density of water is 62.4 lb/R. (6) The tank is full of water and all of the water is to be pumped over the top of the tank. Find the approximate work for the slice as shown. Use Delta or A from the CalcPad. Leave in your answer. 32118.5281 ( 29 - y) Ay Find the endpoints for the integral...
The figure Tank3png shows a water tank where a wall is a vertical flat-plate that is composed of two rectangular faces of areas Ai and A2 with widths w 1.0 m, W2 2.0 m respectively, and one semicircular face of area A3, with radius R 0.5 m. The dimensions h 1.0 m, h2- 1.0 m, as shown in the figure. The density of water, p -103kg/m3, acceleration due to gravity, g = 10 m/s The figure 4 shows a water...