Problem 4-2-8 Water, at 150 kPa and 12 C, is heated in a mixing chamber, at...
Liquid water at 300 kPa and 25°C is heated in a chamber by mixing it with steam at 300 kPa and 200°C as in the figure below. Liquid water enters the chamber at a rate of 3.0 kg/s, and the chamber is estimated to lose heat to the surrounding air at 25°C at a rate of 35 kW. If the mixture leaves the mixing chamber at 300 kPa and 120°C, establish: a. Mass flow rate of the superheated steam, kg/s...
please solve all of them awestion 3 (35 pts) water at Tjz1SC is heated in a chamber by mixing it with steam at paa300 kPaond TR320С The saturated liquid water and the steam enter the mibxing chamber through separate and independent inlet pipes. The saturated liquid water enters the mixing chamber at a rate of 3.0 kg/s, and the chamber loses heat to the surrounding air at 30 Cat a rate of 12 kW. The mixture leaves the mixing chamber...
Liquid water at 300 kPa and 20°C is heated in a chamber by mixing it with hot water at 300 kPa and 90°C. Cold water enters the chamber at a rate of 1.8 kg/s. If the mixture leaves the mixing chamber at 60°C, determine the mass flow rate of the hot water required
A mixing chamber operates steadily at 200 kPa with 2 kg/s of saturated liquid H2O mixing with 1 kg/s of superheated steam at 250°C. Determine the exit specific enthalpy and exit temperature if the heat transfer rate into the mixing chamber is 150 kW throughout this process. Note: I know how to solve for the exit specific enthalpy, but I am not sure how to solve for the exit Tempurature. Could you please show me how to solve for the...
1. A steam turbine has an inlet of 2 kg/s water at 1000 kPa and 350 °C with a velocity of 15 m/s. The exit is at 100 kPa, 150 °C, and very low velocity. Determine the power produced. 2. A small expander (a turbine with a heat transfer) has 0.05 kg helium entering at 1000 kPa, 550 K, and it leaves at 250 kPa, 300 K. The power output on the shaft is measured at 55 kW. Determine the...
Problem 4 Saturated water vapor at 150 kPa is condensed to saturated liquid in a steady-flow, isobaric heat exchanger. The released heat is transferred to the surrounding air whose temperature is at 20°C Determine the total entropy generation per unit mass associated with this process.
NO INTERPOLATION REQUIRED Air enters an adiabatic turbine at 1000 kPa and 1625 degrees C (state 1) with a mass flow rate of 5 kg/s and leaves at 100 kPa the isentropic efficiency of the turbine is 85%. Neglecting the kinetic energy change of the steam, and considering variable specific heats, determine: a. the isentropic power of the turbine Isentropic power in kW b. the temperature at the turbine exit temperature at exit in degrees C c. the actual power...
20 ℃ Liquid water is flowing into a chamber with a mass flow rate of 1.5 kg/s and heated by mixing it with a superheated steam at 300 ℃. For a specified mixing temperature at 60 ℃, what is the mass flow rate of the steam we need to set and what is the mass flow rate of the 60 ℃ water we can get? Assume: • Mass flow rate ?̇ is the mass change per unit time, with the...
1 pts Cold water at 10°C flowing a rate of 2 kg/s is heated to 35°C inside a heat exchanger by saturated steam. The steam enters the heat exchanger as saturated vapor at 100 kPa and leaves as saturated liquid at the same pressure. The heat exchanger losses heat at a rate of 20 KW. The mass flow rate of the steam is most nearly: 0.185 0.101 0.748 0.548 0.312 0.243 0.443 0.085
03 4: Air from the surrounding atmosphere at 100 kPa, 20 °C, enters a compressor with a velocity of 8.6 m/s through an inlet whose diameter is 36 cm. The compressed air exits at 650 kPa, 225 °C, with a velocity of 2.8 m/s. The rate of entropy generation for the compressor is 0.062 kW/K Determine the power input to the compressor, kW.