***************************************************************************************************
Check the answer and let me know immediately if you find
something wrong... I will rectify the mistakes asap if any
1 points GiancoliWA7 18 An electronic device designed to operate at any temperature in the range...
An electronic device designed to operate at any temperature in the range from −6.0°C to 65.4°C contains pure carbon resistors. What is the percent difference in resistance over this range? The temperature coefficient of resistivity for carbon is −0.500 ✕ 10-3/°C.
stuck on these 2 questions 1. A resistor made of Nichrome wire is used in an application where its resistance cannot change more than 2.53% from its value at 20.0°C. What is the highest temperature at which this resistor can be reliably used? The temperature coefficient of resistivity for Nichrome is 0.4 ✕ 10−3 (°C)−1. 2. An electronic device designed to operate at any temperature in the range from −9.9°C to 78.7°C contains pure carbon resistors. What is the percent...
nand a cross sectional area of 0.270 mm2. If the resistivity of copper is 1.70 x 10 m and a potential difference of 0.500 V is maintained across its lenqth, determine the current in has a length of 1.50 the wire (In A) Need Help? Read It -1 points SerPSE10 26.3.0P010 M Ask Your Teacher My Notes f the magnitude of the drift velocity of free electrons in a copper wire i 10 m/s. what the electric field in the...
10. -11 points SerPSE 10 26.4.OP.011. My Notes Ask Your Teacher A physics student is studying the effect of temperature on the resistance of a current carrying wire. She applies a voltage to a iron wire at a temperature of 53.0°C and notes that produces a current of 1.40 A. If she then applies the same voltage to the same wire at -88.0°C, what current should she expect (in A)? The temperature coefficient of resistivity for iron is 5.00 x...
8. + -/1 points SerPSET9 32.P.047. My Notes + Ask Your Teacher In the circuit of the figure below, the battery emf is 65 V, the resistance R is 150 1, and the capacitance C is 0.500 uF. The switch S is closed for a long time interval, and zero potential difference is measured across the capacitor. After the switch is opened, the potential difference across the capacitor reaches a maximum value of 150 V. What is the value of...
My Notes Ask Your Tea points You have builtぁdevice that measures the temperature outside and displays it on dial as a measure of how far away from room temperature outside is. The way the dial works is that a needle with charged ball on the end is placed between two charged parallel plates. The strength of the uniform electric field between the plates is proportional to the outside temperature. Given that the charged ball on the needle has a charge...
A steel block of mass 6.4 kg is originally at a temperature of
18°C and 1 atm.
A steel block of mass 6.4 kg is originally at a temperature of 18°C and 1 atm. It is then heated to a temperature of 68°C without any change in pressure. The specific heat of steel is 452 J/(kg . °C), its density is 7.85 x 103 kq/m3, and the coefficient of linear expansion is 12 x 10-6/oc. (a) Determine the work done...
8. [-14 Points] DETAILS SERPSE10 30.1.OP.008.CTX. MY NOTES ASK YOUR TEACHER You are a technician at an MRI center. One day some medical students enter your lab for a training session. One of them asks about metal in the MRI room, and you clearly state that that is a dangerous situation. The questioner does not look convinced, so you provide the following example. Suppose a woman enters the MRI machine and has forgotten to remove a silver choker necklace. The...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...