The ng beam in (Figure 1) is supported by the three suspender bars Bars AB and EF are made of aluminum and bar CD is made of steel.
The ng beam in (Figure 1) is supported by the three suspender bars Bars AB and EF are made of aluminum and bar CD is made of steel
The rigid beam in (Figure 1) is supported by the three suspender bars. Bars AB and EF are made of aluminum and bar CD is made of steel. Part A If each bar has a cross-sectional area of \(480 \mathrm{~mm}^{2}\), determine the maximum value of \(P\) if the allowable stress is \(\left(\sigma_{\text {allow }}\right)_{\text {st }}-190 \mathrm{MPa}\) far the steel and \(\left(\sigma_{\text {allow }}\right)_{\text {al }}-150 \mathrm{MPa}\) for the aluminum. \(E_{\text {st }}-200 \mathrm{GPa}, E_{\text {al }}-70 \mathrm{GPa}\).
The rigid beam ACE is subjected to the load P and suspended at points A, C, and E by three suspender bars AB, CD, and EF (see Figure 1). These three suspender bars are made of the same steel and have the same circular cross section with the same diameter of d=30 mm. The ultimate 2m stress of steel is σu=450 MPa and Young modulus is E=200 GPa. (a) Using a factor of safety FS=1.5, determine the All maximum allowable load...
A system of bars consists of a steel bar (AB) and an aluminum bar (BC). Bar AB has a cross-section of 2 inches by 0.75 inches and has a modulus of elasticity of 29000 ksi and a coefficient of thermal expansion of 6.5X10-6 /F. Bar BC has a cross-section of 3 inches by 0.75 inches and has a modulus of elasticity of 10600 ksi and a coefficient of thermal expansion of 12.8X10-6 /F. A gap of 0.03 inches exists between...
Question 2 A rigid bar is FEBC is supported by two steel deformable bars AB and DE, as shown in the figure. There is no strain in the vertical bars before the load P is applied. After the load P s applied, the normal strain in bar DE is 0.0006 mm/mm. Determine the normal strain in bar AB. 1.2 m 0.9 m E Rigid 1.5 m
practice exam for mechanic of material Problem #3: The rigid be m The rigid beam ACE is u sed the suspender bars. Bars AB der hars Bars AB and EF are made of aluminum and har CD is made of steel. Each barha and bar CD is made of steel Fach har has a cross-sectional area of 900 mm, Ex - 200 GPa, E-70 GPa P-20 KN. al 2 m 5 -15 Fox 190 0 3 FAQ +15 Foc 390...
The device is used to retur a change in temperature Bars AB and CD made of A-s steel and 2014- TO aluminum alloy respectively. When the temperature is at 35 C, ACBs in the po Figure 1) Part A Determine the vertical power of the whether to Express your answer to the significant figures and include the propriate units. Ente positive value the displacement is upward and negative or if the displacement is downward. Figure WA Value Units Suterit <...
blem 5 (25 points): Consider the system of bars shown below. Bars AB, CD, and EF are connected d link BED. Determine the horizontal displacement of point F B by a rigid . Bar AB has a cross-sectional area of 0.012 m2, a Young's modulus of 200 GPa, and a length of 0.34 m. . Bar CD has a cross-sectional area of 0.010 m2, a Young's modulus of 200 GPa, and a length of 034 m . Bar EF has...
The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected to an axial load of 50 kN E = 199 GPa, st = 0.30. Part A Determine the change in its length Express your answer to three significant figures and include appropriate units. THẢ * * * G3 ? BAD Value Units Submit Request Answer Part B Figure Determine the new height at section - Express your answer to six significant figures and include...
3 3. (25 pts.) A system of bars consists of a steel bar (AB) and an aluminum bar (BC). Bar AB has a cross-section of 2 inches by 0.75 inches and has a modulus of elasticity of 29000 ksi and a coefficient of thermal expansion of 6.5x10-6 /F. Bar BC has a cross-section of 3 inches by 0.75 inches and has a modulus of elasticity of 10600 ksi and a coefficient of thermal expansion of 12.8x106/F. A gap of 0.03...
Review Part A The assembly consists of a cantilevered beam CB and a simply supported beam AB (Figure 1). If each beam is made of A-36 steel and has a moment of inertia about its principal axis of determine the displacement at the center D of beam BA. 136 in4 Express your answer to three significant figures and include appropriate units. AD = Value Units Submit Figure 1 of 1 15 kip Provide Feedback 8 ft 16 ft Review Part...