The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected...

Question

Question

The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected to an axial load of 50 kN E = 199 G

The rod beam in (gure 1) is supported by the three suspendarban Bars AB and EF are made of minum and bar CD is made of steel

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

Solution; SIAD - SLAB & Shoot Sko - PXLAB & Plac & PX Leo PABX EST ABCX Est Acoxlst I SLOp = PXLAB & PXlBC PX lco ChABX WA BO

Add a comment

Answer 2

Similar Homework Help Questions

The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected...

The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kN. Est = 196 GPa, Vst=0.33 Part B Determine the new height at section a-a. Express your answer to six significant figures and include appropriate units. μΑ Value Units Submit Request Answer Part C Figure < 1 of 1 Determine the new width at section a-a. Express your answer to six significant figures and include appropriate units. SO...
The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kN. Est = 193 GPa, vst=0.30.

The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kN. Est = 193 GPa, vst=0.30. Part A Determine the change in its length. Express your answer to three significant figures and include appropriate units.Part B Determine the new height at section a-a. Part CDetermine the new width at section a-a.
Each bar of the truss shown in the figure below has a diameter of 20 mm...

Each bar of the truss shown in the figure below has a diameter of 20 mm Suppose that P = 36 kN (Figure 1) Part A Determine the average normal stress in bar BC of the truss. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. σ1e* Value Units Submit Request Answer Part B Determine the average normal stress in the...

Full solution thank The 12-m-long A-36 steel rails on a train track are laid with a...

Full solution thank The 12-m-long A-36 steel rails on a train track are laid with a small gap between them to allow for thermal expansion. The CROSS-sectional area of each railis 3100 mm . (Figure 1) - Part A Determine the required gap & so that the rails just touch one another when the temperature is increased from Ti -30°C to 30°C Express your answer to three significant figures and include the appropriate units. :MAO ? Value Units Fiqure 1...
Part A Consider the structure shown in (Figure 1). Assume the members are pin-connected at A,...

Part A Consider the structure shown in (Figure 1). Assume the members are pin-connected at A, B, and C. Suppose that P = 7.5 kN. Determine the horizontal component of reaction at the support A. Express your answer to three significant figures and include the appropriate units - TuÃ • • • Ea ? A - Value Units Submit Request Answer Figure 1 of 1 > Part B Determine the vertical component of reaction at the support A. Express your...
Review The truss is supported by a pin at A and a roller at B. (Figure...

Review The truss is supported by a pin at A and a roller at B. (Figure 1) Determine the support reaction at B. Express your answer to three significant figures and include the appropriate units. LE THẢ * * 0 Ea ? B, - Value Units Submit Request Answer Part C Determine the horizontal component of reaction at A. Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 ? CHA Value O Units...

Problem 8.42 The beveled gear is subjected to the loads shown in the figure below (Figure...

Problem 8.42 The beveled gear is subjected to the loads shown in the figure below (Figure 1). The shaft has a diameter of 0.5 in, and is fixed to the wall at C. Part A Determine the normal stress acting at point A. Express your answer to three significant figures and include appropriate units. ЦА ? (CA), - Value Units Submit Request Answer Part B Determine the shear stress acting along the yr plane at point A. Express your answer...
The steel beam has the cross-sectional area shown in (Figure 1) Part A Determine the largest...

The steel beam has the cross-sectional area shown in (Figure 1) Part A Determine the largest intensity of the distributed load to that the beam can support so that the maximum bending stress in the beam does not exceed 160 MPa Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 Value Units Submit Request Answer Provide Feedback
Bar AB has the angular motions shown. Suppose that WAB = 5 rad/s and a AB...

Bar AB has the angular motions shown. Suppose that WAB = 5 rad/s and a AB = 6.6 rad/s2. (Figure 1) Part A Determine the velocity of the slider block C at this instant Express your answer to three significant figures and include the appropriate units. ? (vc. = Value Units Submit Request Answer Part B Figure < 1 of 1 Determine the acceleration of the slider block C at this instant. Express your answer to three significant figures and...

The wide-flange beam is subjected to the loading shown in (Figure 1). Suppose that P =...

The wide-flange beam is subjected to the loading shown in (Figure 1). Suppose that P = 25 kN. Follow the sign convention. Part A Although it is not very accurate, use the shear formula to determine the shear stress developed at point A. Express your answer to three significant figures and include the appropriate units. CE MÅ Value O O ? Units Submit Request Answer - Part B Figure < 1 of 1 > Determine the principal stress 01 at...

The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected...

Homework Answers

Add Answer to:
The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected...

Post as a guest

Earn Coins

The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected...

The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kN. Est = 193 GPa, vst=0.30.

Each bar of the truss shown in the figure below has a diameter of 20 mm...

Full solution thank The 12-m-long A-36 steel rails on a train track are laid with a...

Part A Consider the structure shown in (Figure 1). Assume the members are pin-connected at A,...

Review The truss is supported by a pin at A and a roller at B. (Figure...

Problem 8.42 The beveled gear is subjected to the loads shown in the figure below (Figure...

The steel beam has the cross-sectional area shown in (Figure 1) Part A Determine the largest...

Bar AB has the angular motions shown. Suppose that WAB = 5 rad/s and a AB...

The wide-flange beam is subjected to the loading shown in (Figure 1). Suppose that P =...

The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected...

Homework Answers

Add Answer to: The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected...

Post as a guest

Earn Coins

Add Answer to:
The stool bar has the original dimensions shown in the Siguro. (Figure 1) It is subjected...