R105 m Problem #1 (3e ruines) A rigid circular plate of 123.mm radius is attached to...
Problem 1. A circular plate of radius 4 is heated. The temperature at point (x, y) on the plate is given by f(z, y) =2x2 + 3y2-4r +5 Assume (0.0) is the center of the plate. (a) (9 points) Find the hottest and coolest points on the edge of the plate (b) (3 points) Is there a point inside the disc that is hotter? Is there a point that's cooler? Problem 1. A circular plate of radius 4 is heated....
Problem 5 Two 180 mm-long rubber bars are fixed at the bottom and attached at the top to a rigid disk of radius 20 mm, as shown below. If the rigid disk is rotated about its center by 2°, determine the shear strain in the rubber at point C (same as point A). ur= 20 mm 180 mm
3) (40 pts) The EXTERNAL 35 kN force P is applied to the end of a 2 m long cantilever beam with the given cross section. The force acts through the shear center, forming an angle of 35 with the horizontal axis. The x, y axes pass through the centroid C. The y-axis can be assumed to coincide with the right- hand edge of the vertical section. Determine (a) the normal bending stress at Point A, (b) normal bending stress...
practice exam for mechanic of material Problem #3: The rigid be m The rigid beam ACE is u sed the suspender bars. Bars AB der hars Bars AB and EF are made of aluminum and har CD is made of steel. Each barha and bar CD is made of steel Fach har has a cross-sectional area of 900 mm, Ex - 200 GPa, E-70 GPa P-20 KN. al 2 m 5 -15 Fox 190 0 3 FAQ +15 Foc 390...
Element 1 is a steel bar that has a circular cross-section with a radius of 30 mm. Element 2 is an aluminum bar that has a circular cross-section with a radius of 50 mm. Element 3 is a steel bar that has a circular cross- section with a radius of 60 mm. Assume for steel, the moduļus, E, is 2.0E11 Pa, and the density, p, is 7800 kg/m3. Assume for aluminum, E-7.0E10 Pa, and p-2700 kg/m3. The rigid, massless rod...
i Problem 4: The stress induced by torsion on a circular cross-section is: 11 problems) (A) Maximum at the center line of the member (B) Maximum at the outer surface of a member (C) Constant throughout the section for a member in the elastic range (D) Always negligible Problem 5: The normal stress,, is zero on a cross-section of a bear under bending M (A) at the neutral axis (B) at the top (C) at the bottom (D) along each...
6. A capacitor with closely spaced circular plates of radius a is charged to potential p. Find E(z) at a point outside, on the axis at distance z from the center much greater than the plate separation. [Hint: The capacitor is equivalent to a thin disk-shaped electret, which in turn is analogous to a similar magnet. Use the known solution for the B-field in a related current configuration. Ans: E. p 6. A capacitor with closely spaced circular plates of...
Pulley Diameter = 800 mm Base Plate Diameter = 1200 mm Shaft Mounted Wheel Axial force F2 along the shaft axis Belt connected to motor with tension force F Figure 1. Side View Belt Bearing A. Bearing B FR = 2 kN --- - - - - - - - - - - > ---- 500 mm 500 mm 500 mm F1 = 500 N 'Fw = 1 kN Figure 2. The design of a fatigue test machine for car...
Guys please help Name Problem 1 (25 points) A rigid beam is supported by three posts A. B and C, and subjected to load P (P-130 KN). Post A and C have a diameter 60 m Post B has a diameter 30 and are made of aluminum (Young's modulus Eal-70 GPa). mm and is made of brass (Young's modulus E-100 GPa). (1) Draw free body diagram for the rigid beam and write down the equilibrium equation (1o points) (2) Is...