Homework Answers
Add Answer to:
rpo 16-1 hp 2.0 5 Question 5. A tensile stress is applied along the long axis...
Draw a schematic stress-strain diagram for steel. Make sure you mark all the important points and regions on it
1. Draw a schematic stress-strain diagram for steel. Make sure you mark all the important points and regions on it. Provide a one-two sentence explanation for each point and region along the diagram. 2. A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa (30 x 10* psi) and an original diameter of 10.2 mm (0.40 In.) will experience only elastic deformation when a tensile load of 8900 N (2000 Ibe) is applied. Compute the maximum length...
1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m...
1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. What is the Poisson's Ratio of this material? 2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 6660 N. If the length of the rod is 380 mm, what must the diameter be to allow an elongation of 0.50 mm? A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of 15,700 N produces a reduction in the specimen diameter of 5 10-3 mm. Compute...
(1 point) In a uniaxial test, a force applied along the axis of a steel cylindrical...
(1 point) In a uniaxial test, a force applied along the axis of a steel cylindrical specimen causes elastic deformation. Given that its initial diameter is 25 mm, determine the magnitude of this force that will produce a 6 mm elastic change in diameter. For steel, v = 0.30 and E = 207 GPa.
Problem 04: A cylindrical metal specimen 15.0 mm in diameter and 150 mm long is to be subjected to a tensile stress of 50 MPa
Problem 04: A cylindrical metal specimen 15.0 mm in diameter and 150 mm long is to be subjected to a tensile stress of 50 MPa; at this stress level the resulting deformation will be totally elastic. (a) If the elongation must be less than 0.072 mm, which of the metals in following Table are suitable candidates? Why? (b) If, in addition, the maximum permissible diameter decrease is 2.3 x 10-3 mm when the tensile stress of 50 MPa is applied,...
2. A steel bar 100 mm long and having a square cross section 20 mm on...
2. A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension with a load of 89,000 N and experiences an elongation of 0.10 mm. Assuming that the deformation is entirely elastic, calculate the elastic modulus of steel. Give your answer in GPa. 3. A zinc single crystal is being pulled in tension with the normal to its basal plane (0001) at 60° to the tensile axis and the slip...
rn A specimen of copper having a rectangular cross section 15.2 mm x 19.1 mm is...
rn A specimen of copper having a rectangular cross section 15.2 mm x 19.1 mm is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain. Round off the answer to three significant figures. Answer: 1.394e-3 A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa and an original diameter of 10.2 mm experiences only elastic deformation when a tensile load of 8900 N is applied. Compute the maximum length of...
1. Chapter 9. Problem#1 (40p): Consider a single crystal FCC iron oriented itch tensile stress applied along |122] direction. A) (10p) Draw a unit eell and show there: the plane (111), tensile di...
1. Chapter 9. Problem#1 (40p): Consider a single crystal FCC iron oriented itch tensile stress applied along |122] direction. A) (10p) Draw a unit eell and show there: the plane (111), tensile direction, normal to the plane direction and slip directions (110,(101] and lo11) B) (10p) Compute the resolved shear stress in (MPa) on plane (111) along the three slip direction given in (B), when tensile stress of 80 MPa is applied. C) (10p) If the critical resolved shear stress...
uestion 2 5 points Save Answe A cylindrical bar of steel, 15 mm in diameter, is...
uestion 2 5 points Save Answe A cylindrical bar of steel, 15 mm in diameter, is deformed elastically by an application of a tensile force along the bar's long axis. Determine the force that will produce an elastic decrease of 2 microns in the diameter. Consider the elastic modulus of steel to be 200 GPa and its Poisson's Ratio to be 0.30. 32,400 N -32,400 N 15,700 N -15,700 N
(GPa) A cylindrical machine part 250 mm long with a diameter of 10 mm is subjected...
(GPa) A cylindrical machine part 250 mm long with a diameter of 10 mm is subjected to an axial load of 28,500 N. Using the list of materials shown in the table below, answer questions 1 through 2. Yield Strength Young's Modulus Material [MPa] Density (g/cm] Aluminum alloy 255 70 2.75 Steel alloy 400 207 7.85 Titanium alloy 800 110 4.50 Copper alloy 250 110 8.50 Brass alloy 340 100 8.40 1. If the elongation is not to exceed 0.6...
1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. What is the Poisson's Ratio of this material? 2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 6660 N. If the length of the rod is 380 mm, what must the diameter be to allow an elongation of 0.50 mm? A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of 15,700 N produces a reduction in the specimen diameter of 5 10-3 mm. Compute...
(1 point) In a uniaxial test, a force applied along the axis of a steel cylindrical specimen causes elastic deformation. Given that its initial diameter is 25 mm, determine the magnitude of this force that will produce a 6 mm elastic change in diameter. For steel, v = 0.30 and E = 207 GPa.
2. A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension with a load of 89,000 N and experiences an elongation of 0.10 mm. Assuming that the deformation is entirely elastic, calculate the elastic modulus of steel. Give your answer in GPa. 3. A zinc single crystal is being pulled in tension with the normal to its basal plane (0001) at 60° to the tensile axis and the slip...
rn A specimen of copper having a rectangular cross section 15.2 mm x 19.1 mm is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain. Round off the answer to three significant figures. Answer: 1.394e-3 A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa and an original diameter of 10.2 mm experiences only elastic deformation when a tensile load of 8900 N is applied. Compute the maximum length of...
1. Chapter 9. Problem#1 (40p): Consider a single crystal FCC iron oriented itch tensile stress applied along |122] direction. A) (10p) Draw a unit eell and show there: the plane (111), tensile direction, normal to the plane direction and slip directions (110,(101] and lo11) B) (10p) Compute the resolved shear stress in (MPa) on plane (111) along the three slip direction given in (B), when tensile stress of 80 MPa is applied. C) (10p) If the critical resolved shear stress...
uestion 2 5 points Save Answe A cylindrical bar of steel, 15 mm in diameter, is deformed elastically by an application of a tensile force along the bar's long axis. Determine the force that will produce an elastic decrease of 2 microns in the diameter. Consider the elastic modulus of steel to be 200 GPa and its Poisson's Ratio to be 0.30. 32,400 N -32,400 N 15,700 N -15,700 N
(GPa) A cylindrical machine part 250 mm long with a diameter of 10 mm is subjected to an axial load of 28,500 N. Using the list of materials shown in the table below, answer questions 1 through 2. Yield Strength Young's Modulus Material [MPa] Density (g/cm] Aluminum alloy 255 70 2.75 Steel alloy 400 207 7.85 Titanium alloy 800 110 4.50 Copper alloy 250 110 8.50 Brass alloy 340 100 8.40 1. If the elongation is not to exceed 0.6...
Most questions answered within 3 hours.
-
Assume one of your finals has 50 questions on it, and
lucky for you, it's all...
asked 59 minutes ago -
Rice Products in Bangladesh
Business behavior is derived in large part from the basic cultural
environment...
asked 2 hours ago -
The following base sequence is found for a mRNA fragment from
wild-type E. coli: 5'- UAUCAGUAGAUAAUGUAACC-3'...
asked 2 hours ago -
For this exercise, round all regression parameters to three
decimal places.
One of the two tables...
asked 3 hours ago -
What is the 5% level of significance for mean = 3.60, standard
deviation = 0.94, and...
asked 3 hours ago -
Prior to beginning work on this discussion, please read the
article by Hayley Peterson, 15 Companies...
asked 3 hours ago -
Which pair of aqueous solutions, when mixed, will form a
precipitate?
A) NaNO3 and AgC2H3O2
B)...
asked 3 hours ago -
1-Write an algorithm to get two numbers from the user (as
inputs) and calculate the sum...
asked 7 hours ago -
Define white-collar crime. What is the difference between
offender and offense-based definitions of white-collar crime? What...
asked 7 hours ago -
Consider a reaction which is 1st order with respect to A and 1st
order with respect...
asked 8 hours ago -
c++
The length of the hypotenuse of a right-angled triangle is the
square root of the...
asked 8 hours ago -
When a metal rod is heated, not only its resistance but also its
length and cross‐sectional...
asked 8 hours ago