Part Specification/Six Sigma A design team was charged with a Cpk = 1.3 and Nominal of...
Part Specification/Six Sigma
-
A design team was charged with a Cpk = 1.3 and Nominal of Peak Pulse Current of 10μ They measured 30 parts from one of the vendors and found the average to be 10μA, with a standard deviation of 0.2. What should the part specification be set to?
Specification = 10μA +/- __?_____
Homework Answers
Process capacity index is nothing but the statistical measure of process capacity to identify whether output is produced within customer's specification limits. The standard Cpk level is 2.0 for the six sigma process.
Process capacity is the number of times the process fits into the tolerance width. So, higher the value of Cp, the better the process.
Add Answer to:
Part Specification/Six Sigma
A design team was charged with a Cpk = 1.3 and Nominal of...
In-Class Exercise - Cpk Problem Design specifications require that a key dimension on a product measure...
In-Class Exercise - Cpk Problem Design specifications require that a key dimension on a product measure 110 + 13 units. A process being considered for producing this product has with a mean of 110 units and a standard deviation of four units. a. What can you say (quantitatively) regarding the process capability? b. Suppose the process average shifts to 98 units. Calculate the new process capability. c. What can you say about the process after the shift? Approximately what percentage...
A company has just negotiated a contract to produce a part for another firm. In the...
A company has just negotiated a contract to produce a part for another firm. In the process of manufacturing the part, the inside diameter of successive parts becomes smaller and smaller as the cutting tool wears. However, the specs are so wide relative to machine capabilities that it is possible to set the diameter initially at a large value and let the process run for a while before replacing the cutting tool. The inside diameter decreases at an average rate...
As part of the process for improving the quality of their cars, Toyota engineers have identified...
As part of the process for improving the quality of their cars, Toyota engineers have identified a potential improvement to the process that makes a washer that is used in the accelerator assembly. The tolerances on the thickness of the washer are fairly large since the fit can be loose, but if it does happen to get too large, it can cause the accelerator to bind and create a potential problem for the driver. (Note: This part of the case...
As part of the process for improving the quality of their cars, Toyota engineers have identified...
As part of the process for improving the quality of their cars, Toyota engineers have identified a potential improvement to the process that makes a washer that is used in the accelerator assembly. The tolerances on the thickness of the washer are fairly large since the fit can be loose, but if it does happen to get too large, it can cause the accelerator to bind and create a potential problem for the driver. (Note: This part of the case...
Which team statistic is the best variable to use to predict a team's winning percentage? One...
Which team statistic is the best variable to use to predict a team's winning percentage? One pitching, one fielding, and one hitting statistic was measured for each major league baseball team at the end of the 2019 season. The dataset is called "2019 MLB Team Statistics. The three explanatory variables as follows. Earned Run Average (ERA): a pitching statistic Fielding %: a fielding statistic Home Runs: a hitting statistic Wis Loss Win Loss 054 Eamed Run Arome 0978 09892098409609 Fielding...
Solve Part 2 First Name Last Name Please put your name on this test and every...
Solve Part 2
First Name Last Name Please put your name on this test and every page that you submit. Please answer the questions and solve the problem in the proper order [1, 2, 3...] 20 points each. tely precisely, and completely as possible 1. Explain Deming's Funnel Experiment. What did he use it for? 2. Differentiate between Pareto Chart and Cause-and-Effect Diagram. Which one should be used first? 3. Explain "The Central Limit Theorem." Why is it so important...
Question 3 1 pts Two different types of injection-molding machines are used to form plastic parts. A part is considered...
Question 3 1 pts Two different types of injection-molding machines are used to form plastic parts. A part is considered defective if it has excessive shrinkage or is discolored. Two random samples, each of size 300, are selected and 15 defective parts are found in the sample from machine 1 and 8 defective parts are found in the sample from machine 2. What type of hypothesis test should you use to determine if both machines produce the same fraction of...
all part of one big question. please answer parts 5-10 and show work The problem and...
all part of one big question. please answer parts 5-10 and
show work
The problem and the data: A pharmaceutical company has developed a new drug designed to reduce a smoker's reliance on tobacco. Since certain dosages of the drug may reduce one's pulse rate to dangerously low levels, the product-testing division of the pharmaceutical company wants to model the relationship between decrease in pulse rate, y (beats per minute), and dosage, (cubic centermeters). Different dosages of the drug were...
Hello! Could you please write a 6 paragraph summary (5-6 sentences each paragraph) of the below?...
Hello! Could you please write a 6 paragraph summary (5-6
sentences each paragraph) of the below? In the overview, if you
could please describe the information in detail. Please have
completed in 6 days if possible. Thank you!
In 50 Words Or LesS .6TOC combines lean Six Sigma (LSS) and the theory of constraints (TOC) for bottom-line benefits . The method's metrics pyramids and communi- cations allow organiza- tions to retain gains and monitor benefits. · 6TOC goes beyond fac-...
Power Train, Ltd. We have smashing systems for reporting, tracking, and controlling costs on design projects....
Power Train, Ltd. We have smashing systems for reporting, tracking, and controlling costs on design projects. Our planning of projects is better than any I have seen at other companies. Our scheduling seemed to serve us well when we were small and we had only a few projects. Now that we have many more projects and schedule using multiproject software, there are too many occasions when the right people are not assigned to the projects deemed important to our success....
In-Class Exercise - Cpk Problem Design specifications require that a key dimension on a product measure 110 + 13 units. A process being considered for producing this product has with a mean of 110 units and a standard deviation of four units. a. What can you say (quantitatively) regarding the process capability? b. Suppose the process average shifts to 98 units. Calculate the new process capability. c. What can you say about the process after the shift? Approximately what percentage...
A company has just negotiated a contract to produce a part for another firm. In the process of manufacturing the part, the inside diameter of successive parts becomes smaller and smaller as the cutting tool wears. However, the specs are so wide relative to machine capabilities that it is possible to set the diameter initially at a large value and let the process run for a while before replacing the cutting tool. The inside diameter decreases at an average rate...
Which team statistic is the best variable to use to predict a team's winning percentage? One pitching, one fielding, and one hitting statistic was measured for each major league baseball team at the end of the 2019 season. The dataset is called "2019 MLB Team Statistics. The three explanatory variables as follows. Earned Run Average (ERA): a pitching statistic Fielding %: a fielding statistic Home Runs: a hitting statistic Wis Loss Win Loss 054 Eamed Run Arome 0978 09892098409609 Fielding...
Solve Part 2
First Name Last Name Please put your name on this test and every page that you submit. Please answer the questions and solve the problem in the proper order [1, 2, 3...] 20 points each. tely precisely, and completely as possible 1. Explain Deming's Funnel Experiment. What did he use it for? 2. Differentiate between Pareto Chart and Cause-and-Effect Diagram. Which one should be used first? 3. Explain "The Central Limit Theorem." Why is it so important...
Question 3 1 pts Two different types of injection-molding machines are used to form plastic parts. A part is considered defective if it has excessive shrinkage or is discolored. Two random samples, each of size 300, are selected and 15 defective parts are found in the sample from machine 1 and 8 defective parts are found in the sample from machine 2. What type of hypothesis test should you use to determine if both machines produce the same fraction of...
all part of one big question. please answer parts 5-10 and
show work
The problem and the data: A pharmaceutical company has developed a new drug designed to reduce a smoker's reliance on tobacco. Since certain dosages of the drug may reduce one's pulse rate to dangerously low levels, the product-testing division of the pharmaceutical company wants to model the relationship between decrease in pulse rate, y (beats per minute), and dosage, (cubic centermeters). Different dosages of the drug were...
Hello! Could you please write a 6 paragraph summary (5-6
sentences each paragraph) of the below? In the overview, if you
could please describe the information in detail. Please have
completed in 6 days if possible. Thank you!
In 50 Words Or LesS .6TOC combines lean Six Sigma (LSS) and the theory of constraints (TOC) for bottom-line benefits . The method's metrics pyramids and communi- cations allow organiza- tions to retain gains and monitor benefits. · 6TOC goes beyond fac-...
Most questions answered within 3 hours.
-
Oxidative phosphorylation is achieved through chemiosmotic
coupling, which turns chemical energy into osmotic potential energy
that...
asked 55 minutes ago -
Hollywood Shoes would like to maintain their cash account at a
minimum level of $64,000, but...
asked 54 minutes ago -
Proteins CtrA-P, DnaA, and GcrA behave similarly to what
molecule in the Eukaryotic Cell Cycle?
asked 57 minutes ago -
TRUE OR FALSE
In case of a competitive tender procedure, in the request for
quotation, the...
asked 1 hour ago -
I am a little behind please provide some explanation, will
provide thumbs up.
This question considers...
asked 1 hour ago -
Let say the utility function as U(X,Y) = lnX + Y. Show that the
marginal rate...
asked 1 hour ago -
A current of I=8.0A is flowing in a typical extension cord of
length L=3.00m. The cord...
asked 1 hour ago -
1. When balancing the equation H2SO4 (aq) + NaOH (aq) →
Na2SO4(aq) + H2O(aq), would you...
asked 1 hour ago -
Provide a definition of “classification hierarchy” and
illustrate your definition with an example of how and...
asked 1 hour ago -
1. Describe the four main green solvents. Provide one example of
the use of each solvent....
asked 1 hour ago -
International ethics focus on:
1) exploitation of labor
2)corruption
3) environmental impact
4) none of the...
asked 1 hour ago -
Costing Models You work for XYZ trucking and your boss has asked
you to figure out...
asked 1 hour ago