I only need number 6 and the answer is not 0.003998 m ohms
I only need number 6 and the answer is not 0.003998 m ohms Figure 1 shows...
Please solve all for me Q1. An inverting amplifier circuit design has an input resistance R1 = 10 kΩ, and feedback resistance R2 = 25 kΩ and an input voltage source VS = 0.5V. Sketch the circuit diagram and find the voltage gain Av in dB, output voltage vo, input source current is, feedback current i2, and output current io of the amplifier circuit. What is the operating bandwidth of this amplifier circuit? Q2. Design an inverting amplifier circuit...
Good morning, I need help with the following, they all relate to OP Amps. Thanks in advance. 2 value 10.00 points Problem 05.010 An op amp voltage divider Find the voltage gain vo/vs of the circuit given below, where R1-18 kΩ and R2-14 k 2. 20 kΩ R1 1% R2 The voltage gain vo/vs of the circuit is Hints Referene eBook & Resources Hint#1 Check my work 3. 1000 points value Problem 05.025-Voltage follower Calculate the output voltage vo in...
EEET255 Electronics Page 4 of6 QUESTION 3: [25 marks] Figure 3 shows a feedback amplifier circuit R, is the source resistor, R is the feedback resistor and R, is the load resistor. The op-amp has an internal input resistance of R, an intemal output resistance R, and an internal gain of A Apply the "Systematic Analysis" method in this question. Figure 3 3.a State the feedback topology used in the amplifier circuit and which type of feedback amplifier is shown...
Inverting Amplifier Figure 4.2 shows the fundamental configuration of Op-Amp in which it is used as an inverting amplifier. In this configuration the ratio, R2/R1 completely controls the effective gain of the amplifier and it can be verified that the output voltage is equal to Vo = - (R2/R1)Vin R2 100K Q-10V R1 Vinow 20K 1 2 7 V Vo 3 -10v Figure 4.2 Part 1 - Inverting Amp: Procedure 1. Construct the circuit of figure 4.2 using Op-Amp IC...
4. For the amplifier in the figure below use the parameters in the table: +Vcc Re VBE- 0.7V, Ri- 1002, R1-160k2, R2-320k2 R3-200k2, R6-40 k2, Rc-60k2, Vcc- 12V, Ry Do a) Draw the DC equivalent circuit and calculate the Q-point. c) Draw the AC equivalent circuit with the small signal model for the transistor. d) Calculate the voltage gain, Av-Vo/vi. Assume ro infinite. e) Draw the circuit to find the amplifier input resistance (Rin). Calculate Rin f Draw the circuit...
Find the induction process of A, β, Ro, Ri. EXAMPLE 10.10 Figure 10.27 shows a feedback current amplifier formed by cascading an inverting voltage amplifier u witha MOSFET Q. The output current I, is the drain current of Q. The feedback network, consisting of resistors R, and R, senses an exactly equal current, namely, the source current of Q, and provides feedback current signal that is mixed with I, at the input node. Note that the bias arrangement is not...
in great detail plz 1. Figure la shows a CG amplifier with a signal source and loaded with a resistance Ru. Do NOT ignore ro of Q. (50pt) OB Vio o+ Vsig : + 6 G .sis 5 Figure la Figure 1b rotre (a) Derive an expression for Rin (5pt) Hgmro (b) Noting that the current through R is equal to the input current i, derive an expression for the overall voltage gain No/Vsig (5pt) (c) Find Rin and Vo/Vsig...
In Figure 3 shown, V1 = 100 millivolts. Further, R1 = 1Kohm, R2 = 10 Kohm, R3 = 5 Kohm, R4= 5 Kohm, R5 = 10 Kohm and RL = 1Kohm. (i) Determine the amplified output voltage V2 of the op-amp (of open-loop gain A) in circuit shown in Figure 3. (ii) Suppose this amplified voltage V2 becomes the source voltage to a passive circuit as illustrated in Figure.3. Find Thevenin’s equivalent circuit looking at the terminal XY. Hence, determine...
please help 2 - The companying circuit shows a 3-resistor biased JFET to be used as a small signal dc amplifier Determine the values of Rp and Rs so that the transistor will meet a point equal to, Vns 8 V and Ips- 2.25 mA .For the JFET take Ipss-4 mA, Vp-4 V and 1- 0 and V coupling and bypass capacitors, determine the small signal voltage gain Vo Vi - Avi which includes RL , input resistance Ri-y /...
Problem 7 (CLO 3, 4, 11 - Ideal Op-Amps, Design): We will now design an Op-Amp circuit to perform the function where v1 - input voltage 1, input voltage 2, = input voltage 3, Vo = output voltage. It may be helpful to consult your recitation 6 (week 7) results as well as Table 4-3 for this problem. 7.a: Select an Op-Amp configuration for your design. Sketch the Op-Amp configuration with symbolic resistors (Rf, Ri, R2, etc) indicated. Do not...