Which command used to verify port security can be used to determine if the port has been disabled by a port security violation?
A. show running-config
B. show port-security violations
C. show port-security interface interface#
D. debug mac-address table
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Which command used to verify port security can be used to determine if the port has...
PLEASE ATTACH A SCREENSHOT OF THE RE-POPULTATED TABLE AT THE END Objectives Part A: Configure Devices and Verify Connectivity . Part B: Gather Information with Show Commands Tasks Create the following network topology on Packet Tracer Addressing Table 10.10.10.0/24 10 SW1 Device InterfaceIP Address Subnet Mask Default Gateway .1 PC1 10.10.10.1 255.255.255.0 NIA f0/o RTA 10.10.20.1 255.255.255.0NIA f0/1 RTA .1 PC1 255.255.255.010.10.10.1 NIC 10.10.10.10 10.10.20.0/24 PC2 NIC 10.10.20.10 255.255.255.0 10.10.20.1 10 SW2 PC2 Part A: Configure Devices and Verify Connectivity...
Which command(s) can be used to view VLAN membership for all VLANs on the switch? A. show vlan brief B. show membership vlan C. show running-config D. None of the above
1a) Which of the following statements is true? Running SSH on the Telnet port will now be sent across an unencrypted port. Despite the results of the scan, the service running on port 23 is actually Telnet and not SSH, and creates an additional vulnerability Running SSH on port 23 provides little additional security from running it on the standard port. Remote SSH connections will automatically default to the standard SSH port. The use of OpenSSH on its default secure...
Question 19 3 pts (TCO 5) Which command will provide information specific to OSPFv3 routes in the routing table? show ip route ospf show ip route ospfv3 show ipv6 route show ip route ospf show ipv6 route ospf Flag this Question Question 20 3 pts (TCO 5) A network administrator enters the command ipv6 router ospf 64 in global configuration mode. What is the result of this command? The router will be assigned an autonomous system number of 64. The...
The Gnu debugger: A. provides a command-line interface. B. permits the use of breakpoints to control the execution of a program. C. may be used by a C program that has been compiled using the `-debug` flag. D. may be started up in the bash terminal by using the `gdb` command. E. None of the above.
1) How to Create VLAN on Cisco Catalyst Switch #show vlan а. VLAN Name Status Ports 1 default active Gil/0/1, Gil/0/2, Gil/0/3, Gil/0/4 Gil/0/5, Gil/0/6, Gil/0/7, Gil/0/8 config t Interface vlan 20 b. interface range gigabitEthernet 0/1 - 6 switchport access vlan 20 exit c. #show vlan VLAN Name Status Ports 1 default Gil/0/1, Gil/0/2, Gil/0/7, Gil/0/8 Gil/0/3, Gil/0/4, Gil/0/5, Gil/0/6 active active 20 VLAN020 2. How to Delete VLAN on Cisco Catalyst Switch no vlan 20 a. b. show...
- Network security QUESTION 17 We assume that a LAN network includes 7 hosts (A, B, C, D, E. Fand G) which are connected by a switch. The contents of the switch's CAM table is as follows: (Port 1. Host A) - (Port 2. Host B) - (Port 3. Host - Port 4, Host D) - Port S. Hosta-Port 6, Host F) - (Port 7. HostG), Also, we assume that there is/are one or many host(s) that has/have sent fake...
sub-interfaces of a router port (interface) can be used to A-relay packets between VLANs. b-make ethernet switheches obsolete c-enbale link aggrgation d-remove packets going through the roster port e- fragment a VLAN into smaller VLANs
Which command can be used to change the owner of a particular file? (A) chuser (B) chgrp (C) chmod (D) chown
Refer to the exhibit. The output of 'show interface g0/0' command on Router-1 can be used to troubleshoot EIGRP adjacency problem. 30/0 80/1 Router 1 Router 2 OK? Method Status Rlish ip interface brief Interface IP-Address Protocol GigabitEthernet0/0 10.10.0.2 GigabitEthernet0/1 unassigned down vlani unassigned down YES manual up up YES unset administratively down YES unset administratively down O True O False Why does OSPF uses Designated Router(DR)? (choose two? Reduce the number of adjacencies over a multiaccess network To summaries...