(Show all Work) ) Radiant Intensitypge 2 3 Permissible Pulse Handling Capability mA)=t(t), single pulse,い25㎍ ,12m25...
Please use the graphs to answer the following questions. Question 1.1) The forward current/voltage curve of the LED is shown on the figures. What is the forward current IF when the forward voltage VF is 1.5V? (Hint-See Figure 1. (a) 4points Question 1.2) How much forward current you need to double the radiant intensity from the radiant intensity at 100 mA forward current. (choose the closest number) (Hint - See Figure 1 (b) 4points) Question 1.3) What is the forward...
Please help with electrical circuits!!!!!!!!!!!!!! A single pdf file showing ALL work must be received by instructor by 12:00pm, April 15, 2020. The two problems below constitute Test 2 for this semester: Q1 (50 pts): Modified version of Problem 6.21 (d) Solve for the voltage across the 50 resistor in Figure 6.48 (d) using i) Mesh Analysis, ii) Nodal Analysis, AND iii) Superposition. iv) Confirm that all three approaches produce the same answer. Be sure to indicate polarity wherever/whenever appropriate...
Can you please help me answer Task 2.b? Please show all work. fs=44100; no_pts=8192; t=([0:no_pts-1]')/fs; y1=sin(2*pi*1000*t); figure; plot(t,y1); xlabel('t (second)') ylabel('y(t)') axis([0,.004,-1.2,1.2]) % constrain axis so you can actually see the wave sound(y1,fs); % play sound using windows driver. %% % Check the frequency domain signal. fr is the frequency vector and f1 is the magnitude of F{y1}. fr=([0:no_pts-1]')/no_pts*fs; %in Hz fr=fr(1:no_pts/2); % single-sided spectrum f1=abs(fft(y1)); % compute fft f1=f1(1:no_pts/2)/fs; %% % F is the continuous time Fourier. (See derivation...
Referring to the following data sheets calculate the switching loss for the IGBT: Given, E = 400V, ID= 56A, Fs = 18.5kHz, VDS= 300V, VGS= +/- 18V, RG = 22ohm. Turn-on and Turn-off Energy: IGBT Eon E (mWs) Eoff 20 40 80 100 120 60 Ic (A) SKM50GB063D Values Unit Absolute Maximum Ratings Symbol Conditions IGBT VCES T = 25°C Ic To = 25 °C T = 150°C To = 75 °C Cnom | |сем CRM = 2xl nom 600...
A common source amplifier circuit based on a single n-channel MOSFET is shown in Figure 4b. Assume that the transconductance gm-60 mS (equivalent to mA/ V) and drain source resistance, os, is so large it may be neglected. 0) Calculate the open circuit voltage gain Av Yout/ Vis. i) The amplifier has a load of 10 k2. Determine the current gain Va. = 12 V 150k 4k3 Vout Vin 200k GND = 0 V Figure 4b a) State the name...
Need help with schematics for blocks 3, 4 and 5!!!!!! Include all schematics and wiring along with the component values and how you acquired them. Explain how each block functions and label any figures. Need schematics for blocks 3, 4 and 5!!!!!! Goal For your final project you will be asked to design and assemble a system in which you will input a stereo audio signal, mix the channels into a single mono signal, amplify the signal, filter it to...
Based on the document below, 1. Describe the hypothesis Chaudhuri et al ids attempting to evaluate; in other words, what is the goal of this paper? Why is he writing it? 2. Does the data presented in the paper support the hypothesis stated in the introduction? Explain. 3.According to Chaudhuri, what is the potential role of thew alkaline phosphatase in the cleanup of industrial waste. CHAUDHURI et al: KINETIC BEHAVIOUR OF CALF INTESTINAL ALP WITH PNPP 8.5, 9, 9.5, 10,...