Sodium hydroxide, NaOH, solutions can be used to acids such as hydorchloric acid, HCl:
A 0.500 M NaOH solution is used to titrate several aliquots of 25.00 mL of an unknown concentration of HCl. Use the data in the table below to determine the average concentration of the hydrochloric acid solution (starting before the titration) and the standard deviation.
Trial # | Volume NaOH (mL) | Trial # | Volume NaOH (mL) |
1 | 16.01 | 6 | 15.84 |
2 | 15.54 | 7 | 15.89 |
3. | 15.71 | 8 | 15.77 |
4 | 15.62 | 9 | 15.66 |
5 | 15.99 | 10 | 15.55 |
Sodium hydroxide, NaOH, solutions can be used to acids such as hydorchloric acid, HCl: A 0.500...
If 32.12 mL of 3.77 M hydrochloric acid solution, HCl, are titrated with 51.5 mL of sodium hydroxide solution, NaOH, according to HCl(aq) + NaOH(aq) - NaCl(aq) + H2O(1) what is the concentration of the sodium hydroxide solution? (Enter your
Reaction 1: Sodium hydroxide + Hydrochloric acid Volume (mL) of 2.0 M HCl(aq) used 25.2 Initial temperature (°C) of the 2.0 M HCl(aq) 21.63 Volume (mL) of 2.0 M NaOH(aq) used 24.8 Maximum temperature (°C) of the 2.0 M NaOH(aq) 21.96 NaOH and HCl final temperature: 35.14 degrees C Determine the Energy (J) absorbed (+) or released (-) by the solution (qsoln). Determine the Energy (J) absorbed (+) or released (-) by the calorimeter (qcal). Determine the Energy (J) absorbed...
Sodium carbonate, Na2CO3, reacts with hydrochloric acid, HCl, to produce sodium chloride, carbon dioxide and water. Refer to slide 7.18 for a summary of formulae relevant to the calculations below. 2HCl(aq) + Na.CO3(aq) + NaCl(aq) + H2O(l) + CO2(g) 1. Use this reaction to explain what is meant by the terms "acid", "conjugate base" and "salt" 2. Balance the equation for this reaction. 3. A solution was prepared by dissolving 5.00 g of Na2CO3 in water and adding water to...
If 25.00 mL of 0.500 M NaOH is used to titrate 15.00 mL of H2SO4, what is the molarity of the acid? H2SO4 + 2 NaOH - Na, SO4 + 2 H2O Enter your answer using three significant figures and no units.
HCl(aq) + NaOH(aq) → NaCl(aq) + H2O(1) 100.0 mL of 0.500 M HCl is mixed with 300.0 mL of 0.100 M NaOH in a coffee cup calorimeter. Assuming the temperature of the solution was initially 25.0 °C, and the final temperature of the solution was 26.7 °C, calculate the enthalpy of this reaction per mole of HCl. Assume the density of the water and acid and base solutions are all 1.00 g/mL.
Sodium hydroxide reacts with ascorbic acid to produce sodium ascorbate and water. Below is the chemical equation: 2NaOH(aq) + H2C6H60(aq) → Na2C6H606(aq) + 2H20(1) Part A - Standardization of the NaOH Solution Trial 1 Trial 2 Trial 3 --------------- 0.4 g Mass of Ascorbic Acid (g) Moles Ascorbic Acid Moles NaOH based on stoichiometry ----------- NaOH Initial Volume (V;) 0.00 mL -------- -----------m L NaOH final Volume (V) 22.5 mL --------mL ----mL ---ml -----mL ------------mL NaOH Volume Used Vi-V; NaOH...
Calculate the molarity of the HCl. The Sodium hydroxide is 0.1M concentration. Volume of NaOH solution in the burette at the start (mL): 50ml 38.80ml 11.20ml 10ml Volume of NaOH solution in the burette at the end (mL): Volume of NaOH solution delivered to the flask (mL): d Volume of HCl solution in the flask (mL)
In an acid-base titration experiment, a NaOH(aq) solution with a known concentration of NaOH is used to titrate a given volume of an HClO4(aq) solution. At the equivalence point, (A) the volume of added NaOH(aq) equals the volume of HClO4(aq). (B) the concentration of HClO4(aq) equals the concentration of NaOH(aq). (C) the added amount (mol) of NaOH(aq) it just enough to neutralize all HClO4(aq). (D) the amount (mol) of HClO4(aq) exceeds the added amount (mol) of NaOH(aq). (E) the added...
Iron(III) hydroxide reacts hydrochloric acid via the following reaction: Fe(OH)3(aq) + 2 HCl(aq) ⇋ SrCl2(aq) + 2 H2O(l) (5 pts) If the concentration of Fe(OH)3 is 0.00684M, what is the pH of the iron(III)hydroxide solution? (8 pts) If 37.42 mL of 0.00684M iron(III)hydroxide is required to neutralize 25.00 mL of HCl, what is the concentration of the HCl solution in molarity?
1. A volume of ___ mL of 0.100 M NaOH(aq) is required to titrate 0.500 g of potassium hydrogen phthalate (often abbreviated KHP) to the endpoint. 2. A 0.5741 g sample of a monoprotic acid was titrated with 0.1008 M NaOH(aq). If 37.89 mL of sodium hydroxide solution were required for the titration, the molar mass of the monoprotic acid is ___ g/mol.