Can someone tell me if a theoretical yield needs to be
calculated for this experiment? And if so, how do you calculate it?
please show all work. thank you. btw the aniline weighs
6.69g.
Can someone tell me if a theoretical yield needs to be calculated for this experiment? And...
i did the synthesis of aspirin experiment and got the data below. how do you do the theoretical yield? percent yield of the pure aspirin? DATA: Mass of Salicylic Acid: 2.034g Volume of Acetic Anhydride used in synthesis: 4.00ml Mass of filter paper: 0.196g Mass of filter paper plus Aspirin: 1.868g Mass of Aspirin: 1.672g Percent Yield of Pure Aspirin: I Experimental Procedure HAZARD: Sulfuric acid, acetic anhydride and glacial acetic acid are corrosive to the skin. They are also...
for this experiment of syntheis of aspirin, was the product obtained pure (based on color)? how do you know? the color was white Experimental Procedure HAZARD: Sulfuric acid, acetic anhydride and glacial acetic acid are corrosive to the skin. They are also irritants, and all operations in which these substances are used should be carried out under the hood. Prepare a hot-water bath by heating a 400-ml beaker containing about 200 mL of water. 1. Use a centigram balance and...
Please help with question 3. Thank you! Disposal of waste: When necessary, all organic waste must be disposed into the organic waste container, all aqueous waste to the aqueous waste container and all solid waste to the solid waste container. Nothing is disposed in the sink or trash can. Synthesis of acetanilide In a dry small conical vial, dissolve 300 mg (or 30 drops) of freshly distilled aniline in 1.0 mL of 1.0 M hydrochloric acid. Swirl the mixture to...
Write out your separation scheme for this experiment. 1. Heat 75 mL of water to 90 °C in a 250-mL beaker. 2. While the water is being heated, place 250 mg of salicylic acid, 1 drop of 85% phosphoric acid and 0.5 mL of acetic anhydride in a test tube. Add a boiling chip to the mixture and gently shake it in order to mix the reactants. 3. Heat the tube in the beaker of water at 85 - 90...
Please help me find the % yield and asnwer questions 1,2,3,4 de from acetanilide Synthesis of 4-Bromoacetan WORK UNDER THE HOOD In a 10 mL flask fitted with a cork, add 3 mL of acetic acid and 1.6 mL of bromine. Cork the flask tim ready to use Dissolve g of acetanilide (you made this in lab m2) in 15 ml of acetic acid in a 250 MI flask fitted with a stir bar. slowly add a bromine solution while...
Please help! (These are the instructions I had) 1) Preparation of K2[Cu(C2O4)2] 2H2O CuSO4•5H2O + 2K2C2O4•H2O → K2[Cu(C2O4)2]•2H2O + K2SO4 + 5H2O Heat a solution of 2.5g of potassium oxalate monohydrate in 12.5mL of water contained in a 50mL beaker (approx. 90°C). Heat 1.55g of copper sulfate pentahydrate in 3mL of water to about 90°C and add it rapidly, with vigorous stirring to the hot potassium oxalate solution. Set on the bench and allow to cool to room temperature then...
Place 3.0 g of salicylic acid in a 125-ml Erlenmeyer flask. Carefully add, stirring constantly, 6 mL of acetic anhydride, followed by 10 drops of concentrated sulfuric acid. Swirl the contents of the flask so that the reactants are thoroughly mixed. Stopper the flask with a one- hole cork fitted with an inverted Pasteur pipet to prevent condensation of water in the reaction flask during heating on the steam bath. Heat the flask in a boiling-water or steam bath for...
What is the limiting reagent in this experiment? Acetophenone or aqueous bleach? 1. Add about 1.0 g (measured accurately) of acetophenone to 40 mL of the bleach solution (5% NaCl in water - this reactant should be included in your table of reagents!) in a 100 mL round bottom flask equipped with a magnetic stirrer. Clamp the flask in the fume hood above a stir plate. 2. After the initial reaction has subsided, boil the reaction mixture gently for 5...
Find %yield please the product obtained was 0.0870g In the hood, place 100 mu L of aniline in a tared 10 times 75 mm (small) test tube. Place the test cube in a small beaker or Erlenmeyer flask to avoid spillage. Stopper the cube with a cork. Now, using a Pasteur pipet, add (with swirling) 0.5 mL of water, followed by three drops of concentrated HCI. Add 10 mg of decolorizing charcoal (we use the pelletized form, called Nonrit^TM) to...
How does the acetone destroy the unreacted hypochlorite? 1. Add about 1.0 g (measured accurately) of acetophenone to 40 mL of the bleach solution (5% NaCl in water - this reactant should be included in your table of reagents!) in a 100 mL round bottom flask equipped with a magnetic stirrer. Clamp the flask in the fume hood above a stir plate. 2. After the initial reaction has subsided, boil the reaction mixture gently for 5 - 10 minutes using...