Also determine the MEP (mean
effective pressure). I only need the MEP solved and thermal
efficiency.
Also determine the MEP (mean effective pressure). I only need the MEP solved and thermal efficiency.
Diesel Cycle
a. The pressure and temperature at each state in this cycle.
b. The compression ratio.
c. The cutoff ratio.
d. The thermal efficiency.
e. The MEP (mean effective pressure.)
Consider an air-standard Diesel cycle (this means use variable specific heats). The inlet state to the compression process is at 95 kPa and 300 K. At the end of the heat addition process, the temperature is 2150 K and the pressure is 7200 kPa. Accounting for the variation of...
Also find thermal efficiency and the mean effective
pressure please!
Required information An air standard Diesel cycle has a compression ratio of 16 and a cutoff ratio of 2. At the beginning of the compression process air is at 91 kPa and 27C. Account for the variation of specific heats with temperature. The gas constant of air is R-0.287 kJ/kg K. Determine the temperature after the heat addition process. (You must provide an answer before moving on to the next...
I only need the cycle thermal
efficiency solved
Required information An ideal gas is contained in a piston-cylinder device and undergoes a power cycle as follows: 1-2 Isentropic compression from an initial temperature T1 20°C with a compression ratio r 6.5 2-3 Constant-pressure heat addition 3-1 Constant-volume heat rejection The gas has constant specific heats with cv- 0.7 kJ/kg.K and R 0.3 kJ/kg-K. Determine the heat and work interactions for each process, in kJ/kg. (You must provide an answer before...
4. (20 points): In a constant-volume the start. The temperature of air at the beginning of the compre temperature attained in the cycle is 2100°C. Take kar-1.4 and Rar = 0.287 kJ/kg K. Determine. a) The compression ratio b) The thermal efficiency of the cycle c) The work done d) The mean effective pressure (MEP) if Pi = 100 kPa Otto cycle the pressure at the end of compression is 12 times thatt ssion is 40°C. The maximum
4. (20...
please help thermodynamics
a) Explain the methods that can be adopted to increase the thermal efficiency of a vapor power cycle. You may use a T-s diagram to explain your reasons. b) A steam regenerative cycle, shown below, is delivering 100 MW of power. Steam from the boller is supplied to the turbine at 8 MPa. 400°C. After expanding isentropically in the 1st stage turbine to a pressure of 1 MPa, steam is taken to the reheater where Its temperature...
(12 points) An ideal Otto cycle operates with a compression ratio of 10. At the beginning of the compression process, the air is at 101 kPa and 27°C. During the constant volume heat addition process, 790 kJ/kg of heat is transferred to the air. Accounting for variable specific heats with temperature, determine: the maximum temperature during the cycle 1266.862 °C the maximum pressure during the cycle 6239.424 kPa the specific net work output 475.495481 kJ/kg the mean effective pressure (MEP)...
Problem 1 A diesel engine has a compression ratio r = 20 and uses air as the working fluid. The state of air at the beginning of the compression process is P1 = 95 kPa and T = 20°C. However, the isentropic expansion normally occuring between state 3 and state 4 is replaced by a polytropic process along which: Pul.35 = constant. The maximum temperature in the cycle is not to exceed 2200 K. In this analysis, the variation of...
1. Determine the thermal efficiency and the required steam flow rate [kg/s] for a reheat regenerative steam power plant which is to produce 200 MW of electricity. The turbine drives a generator with an efficiency of 94%. The turbine inlet conditions are 160 bar and 590 C; after reheat, the steam is at 100 bar and 590 C; one closed heater is at 30 bar; an open feedwater heater is at 1.5 bar, and the condenser pressure is 0.10 bar....
a) Explain the methods that can be adopted to increase the thermal efficiency of a vapor power cycle. You may use a T-s diagram to explain your reasons. b) A steam regenerative cycle, shown below, is delivering 100 MW of power. Steam from the boiler is supplied to the turbine at 8 MPa, 400° C. After expanding isentropically in the 1st stage turbine to a pressure of 1 MPa, steam is taken to the reheater where its temperature is raised...
mean effective pressure is 8.5 Pecific fuel consumption is 3009 g/kWh, and the indicated A A six-cylinder, four-stroke gasoline engine having a bore of 90 mm and stroke of 100 mm has a compression ratio 8. On test, it develops a torque of 240 Nm when it was running at 2500 rpm. Given that the ratio of the indicated thermal efficiency to the theoretical air standard (a) The calorific (heat) value of the fuel Qv, (2 marks) (b) The indicated...