Homework Answers
Add Answer to:
Q2 (30 marks) A bas has a diameter d-40mm. If it is subjected to a Torque...
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of...
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is attached to the wall at point A and three torques are applied as shown, determine the minimum shear stress developed in the pipe. Answers should be given in units of MPa. 30 N m 20 N m 80 N m For the 30mm diameter shaft shown below made of steel (G-200GPa), what is the magnitude of the total angle of...
The drill is jammed in the wall and is subjected to the torque and force as...
The drill is jammed in the wall and is subjected to the torque and force as the below picture a) Determine the axial force (P), transverse shear (V), torque (T), and bending moment (M) on cross-section a-a. b) Calculate max stresses on the cross-section a-a due to loads P, V, T and M EACH. c) Combine all stress components at point B that is on the a-a section from part b) and draw a stress element at B. Determine the principal stresses at...
A 31-mm-diameter solid shaft is subjected to both a torque of T and show them on...
A 31-mm-diameter solid shaft is subjected to both a torque of T and show them on a stress element. 110 N m and an axial tension load of P 23 N as shown Determine the norma t and shear stresses at 2 Answers: MPa MPa ay MPa
3. The propeller shaft of the tugboat is subjected to the compressive force and torque shown....
3. The propeller shaft of the tugboat is subjected to the compressive force and torque shown. The shaft has an inner diameter of 125 mm and an outer diameter of 175 mm. (20 pts) 0410 KN 2 kNm Determine the following at point A located on the outer surface: avg. TMIP, 8s Principal stresses and Op c Draw Mohr's circle d Draw principal stress and maximum in plane shear stress elements
The splined ends and gears attached to the A992 steel shaft are subjected to the torques...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks] a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
A solid shaft with 100-mm-diameter is made of cast iron and is subjected to the distributed...
A solid shaft with 100-mm-diameter is made
of cast iron and is subjected to the distributed and
concentrated loadings as shown in Figure 9. The shear modulus of
cast iron is 39GPa.
(A) Determine the angle of twist at the free end A of the shaft due
to these loadings. [9 marks]
(B) Determine the maximum shear stress in this shaft. [4
marks]
(C) Cast iron is a brittle material with an ultimate strength of
260MPa. Determine whether this
structure...
A solid tube is subjected to the loading shown. The tube has a diameter of 1.5 in.
A solid tube is subjected to the loading shown. The tube has a diameter of 1.5 in. (a) Determine which internal force quantities would 8in. cause normal stresses and which would cause shear stresses on a cross-section cut through points A and B. (b) Determine the state of stress at point A.(c) Determine the state of stress at point B.
PLEASE PRINT Question Four The beam has a cross section shown below and is subjected to...
PLEASE PRINT
Question Four The beam has a cross section shown below and is subjected to a 1 kN load as shown. The beam AB has a length of 3 m. a) Draw the shear force and bending moment diagrams. b) Determine the maximum bending stress. c) Where is the location of the maximum stress in b) above? 30 mm 30 mm 30 mm 50 mm t 40 mm 50 m 40mm
The splined ends and gears attached to the A992 steel shaft are subjected to the torques...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks) a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
The rod has a diameter of 40 mm. (Figure 1) It is subjected to the force system Fx = 1140 N, Fy = 560 N, Fz = 950 N.
The rod has a diameter of 40 mm. (Figure 1) It is subjected to the force system Fx = 1140 N, Fy = 560 N, Fz = 950 N.Part A Determine the normal stress that acts at point A. Part B Determine the shear stress Txy that acts at point A. Part C Determine the shear stress Txz that acts at point A.
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is attached to the wall at point A and three torques are applied as shown, determine the minimum shear stress developed in the pipe. Answers should be given in units of MPa. 30 N m 20 N m 80 N m For the 30mm diameter shaft shown below made of steel (G-200GPa), what is the magnitude of the total angle of...
A 31-mm-diameter solid shaft is subjected to both a torque of T and show them on a stress element. 110 N m and an axial tension load of P 23 N as shown Determine the norma t and shear stresses at 2 Answers: MPa MPa ay MPa
3. The propeller shaft of the tugboat is subjected to the compressive force and torque shown. The shaft has an inner diameter of 125 mm and an outer diameter of 175 mm. (20 pts) 0410 KN 2 kNm Determine the following at point A located on the outer surface: avg. TMIP, 8s Principal stresses and Op c Draw Mohr's circle d Draw principal stress and maximum in plane shear stress elements
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks] a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
A solid shaft with 100-mm-diameter is made
of cast iron and is subjected to the distributed and
concentrated loadings as shown in Figure 9. The shear modulus of
cast iron is 39GPa.
(A) Determine the angle of twist at the free end A of the shaft due
to these loadings. [9 marks]
(B) Determine the maximum shear stress in this shaft. [4
marks]
(C) Cast iron is a brittle material with an ultimate strength of
260MPa. Determine whether this
structure...
PLEASE PRINT
Question Four The beam has a cross section shown below and is subjected to a 1 kN load as shown. The beam AB has a length of 3 m. a) Draw the shear force and bending moment diagrams. b) Determine the maximum bending stress. c) Where is the location of the maximum stress in b) above? 30 mm 30 mm 30 mm 50 mm t 40 mm 50 m 40mm
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks) a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
Most questions answered within 3 hours.
-
Please answer true or false. Words
cannot be changed or added in to make it true...
asked 53 minutes ago -
An empty test tube weighs 15.923 grams. Then,
MgCl2•6H2O is added into the test tube. After...
asked 55 minutes ago -
(a) A piston at 6.1 atm contains a gas that occupies a volume of
3.5 L....
asked 54 minutes ago -
Assume memory access is 10 units of time and disk access is
10000 units of time....
asked 1 hour ago -
1. Are all good samples random?
2. Magazines often report surveys giving statistics such as “63%...
asked 1 hour ago -
Under all the various types of market structures, firms
must eventually earn some economic profits for...
asked 1 hour ago -
Consider the following fitness regime for a single locus trait
with two co-dominant alleles: w11 =...
asked 1 hour ago -
A large cable company reports the following.
80% of its customers subscribe to its cable TV...
asked 1 hour ago -
Please answer the question in brief.
Discuss the role of ERP in organizations. Are ERP tools...
asked 1 hour ago -
Discuss the pros and cons of collaborative software such
as SameTime. Does it increase productivity? What...
asked 1 hour ago -
Buying your in-laws a gift because it’s expected is
due to the ____________ motive of gift-giving....
asked 1 hour ago -
Calculate the expected value, the variance, and the standard
deviation of the given random variable X....
asked 2 hours ago