Homework Answers
1) draw the front view with
the considered dimensions
2) extended the length in the front view towards upward to get the length of the top view
3) the slot on the top merges in the top view
4) Now, draw the 45°line with horizontal
5) produce the lines from the points in the top view to touch the 45°line and then produce them vertically downwards
6) also produce lines from points in the front view to intersect the lines which we drawn in the previous step
7) Specify the intersected points and draw the side view
8) In side view, the length becomes width of the top view and height is same as height of the front view
Add Answer to:
2. Draw the orthographic projections - front, top and right side views for the given figure...
Given: The front and top views of an object. Required: Draw the right side view and...
Given: The front and top views of an object.
Required: Draw the right side view and complete the bottom half
as instructed.
For part 2: Draw the right side view of surface
14,17,19,20,26.
ORTHOGRAPHIC READING GIVEN: The front and top views of an object. 10 REQUIRED: Draw the right side view and complete the bottom half as instructed. 13 14 15 16 17 18. 26 20 22 Draw the right side view of surface 14,17,19,20,26. 14 26
2. Draw multiviews below (here they are top, front and right side views) as front, top...
2. Draw multiviews below (here they are top, front and right side views) as front, top and left-side view and add mising lines. Use red pencil for missing lines. And please watch the video named missing lines) that I uploaded on Ims for help. the missing line EXAMPLE 1 Soun 986622ELA DUOLE
sketch an isometric view given top front and right views. ㄚ Top, Front & the side...
sketch an isometric view given top front and right
views.
ㄚ Top, Front & the side views are given. Sketch an isometric view.
2-(20%) Use the three orthographic views given below and freehand sketch the oblique view. The drawing...
2-(20%) Use the three orthographic views given below and freehand sketch the oblique view. The drawing should be somewhat proportional. TOP FRONT RIGHT SIDE
Isometric & Oblique 1. Given the front, top and right side views of the object, sketch...
Isometric & Oblique 1. Given the front, top and right side views of the object, sketch the Isometric pictorial of the object. You may use isometric grid paper if desired. Keep the object in proportion. TOP Zoo FRONT RIGHT SIDE 2. Given the front and top views of the object, sketch the Oblique Cavalier pictorial of the object on Engineering paper at 30 degrees. Keep the object in proportion. - - ТОР FRONT
PLEASE DRAW THIS IN AUTOCAD TOP FRONT AND RIGHT SIDE VIEWS INCLUDE HIDDEN AND CENTER LINES...
PLEASE DRAW THIS IN AUTOCAD
TOP FRONT AND RIGHT SIDE VIEWS
INCLUDE HIDDEN AND CENTER LINES
8. Below 1.00 1.50 0.75 2.50 2 x 0.50- 1.50
Given the front and left side use 45 angle projection and draw the top view. then complete anothe...
given the front and left side use 45 angle projection and draw
the top view. then complete another 3 orthographic views by first
drawing the front view revolved clockwise on A as a pivot until
milled slot is horizontal for cutting on a milling machine, then
project top and left side. dimension all views.
Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50
Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50
given the top and right side views, sketch the front view as a full section SECTIONA-A...
given the top and right side views, sketch the front view as a
full section
SECTIONA-A SECTION B-B SECTION C-C
Draw the necessary orthographic views to describe the object in Figure D2. The drawing shall incl...
Draw the necessary orthographic views to describe the object in Figure D2. The drawing shall include the following views: a HALF SECTIONAL FRONT view from A a SIDE view from B ALL DIMENSIONS ARE IN MILLIMETRES PLOT THE DRAWING ON A SCALE OF 1:2. 58 32 0132 0115 5116 φ100 ф86 R4 φ64 010 THRU R3 070 ALL UNMARKED RADIIR 30 050 THRU в/
Draw the necessary orthographic views to describe the object in Figure D2. The drawing shall include...
Sketch the object represented by the orthographic projection. TOP TOP FRONT FRONT SIDE TOP 0861 01...
Sketch the object represented by the orthographic projection. TOP TOP FRONT FRONT SIDE TOP 0861 01 FRONT FRONT
Given: The front and top views of an object.
Required: Draw the right side view and complete the bottom half
as instructed.
For part 2: Draw the right side view of surface
14,17,19,20,26.
ORTHOGRAPHIC READING GIVEN: The front and top views of an object. 10 REQUIRED: Draw the right side view and complete the bottom half as instructed. 13 14 15 16 17 18. 26 20 22 Draw the right side view of surface 14,17,19,20,26. 14 26
2. Draw multiviews below (here they are top, front and right side views) as front, top and left-side view and add mising lines. Use red pencil for missing lines. And please watch the video named missing lines) that I uploaded on Ims for help. the missing line EXAMPLE 1 Soun 986622ELA DUOLE
sketch an isometric view given top front and right
views.
ㄚ Top, Front & the side views are given. Sketch an isometric view.
2-(20%) Use the three orthographic views given below and freehand sketch the oblique view. The drawing should be somewhat proportional. TOP FRONT RIGHT SIDE
Isometric & Oblique 1. Given the front, top and right side views of the object, sketch the Isometric pictorial of the object. You may use isometric grid paper if desired. Keep the object in proportion. TOP Zoo FRONT RIGHT SIDE 2. Given the front and top views of the object, sketch the Oblique Cavalier pictorial of the object on Engineering paper at 30 degrees. Keep the object in proportion. - - ТОР FRONT
PLEASE DRAW THIS IN AUTOCAD
TOP FRONT AND RIGHT SIDE VIEWS
INCLUDE HIDDEN AND CENTER LINES
8. Below 1.00 1.50 0.75 2.50 2 x 0.50- 1.50
given the front and left side use 45 angle projection and draw
the top view. then complete another 3 orthographic views by first
drawing the front view revolved clockwise on A as a pivot until
milled slot is horizontal for cutting on a milling machine, then
project top and left side. dimension all views.
Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50
Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50
given the top and right side views, sketch the front view as a
full section
SECTIONA-A SECTION B-B SECTION C-C
Draw the necessary orthographic views to describe the object in Figure D2. The drawing shall include the following views: a HALF SECTIONAL FRONT view from A a SIDE view from B ALL DIMENSIONS ARE IN MILLIMETRES PLOT THE DRAWING ON A SCALE OF 1:2. 58 32 0132 0115 5116 φ100 ф86 R4 φ64 010 THRU R3 070 ALL UNMARKED RADIIR 30 050 THRU в/
Draw the necessary orthographic views to describe the object in Figure D2. The drawing shall include...
Sketch the object represented by the orthographic projection. TOP TOP FRONT FRONT SIDE TOP 0861 01 FRONT FRONT
Most questions answered within 3 hours.
-
Living in a group could bring several disadvantages to an
individual. What are some of the...
asked 3 minutes ago -
Complete and balance the following reactions. In case of no
reaction occurring write NR.
Mix #1:...
asked 8 minutes ago -
If an economy consumes 75% of any increase in income, then an
increase in autonomous investment...
asked 12 minutes ago -
A shotputter throws the shot with an initial speed of 15.8 m/s
at a 38.0 ∘...
asked 27 minutes ago -
Debra and Merina sell electronic equipment and supplies through
their partnership. They wish to expand their...
asked 28 minutes ago -
How does a linear regression allow you to better estimate
trends, costs, and other factors in...
asked 36 minutes ago -
1. (15%) Describe the difference between a pull (Kanban), push
and CONWIP production systems.
asked 32 minutes ago -
QUESTION 5
The total area under the Z distribution curve is equal to:
a.
10
b....
asked 41 minutes ago -
Using Python
The variables x and y refer to numbers. Write a code segment
that prompts...
asked 55 minutes ago -
If
the coefficient of static friction between a box and the floor is
0.35 with what...
asked 58 minutes ago -
A die is designed to punch holes with a radius of 1.08 10-2 m in
a...
asked 1 hour ago -
government can increase import through
a. export subsidies
b. tax breaks
c. increase import tax
d....
asked 1 hour ago