The solid steel shafts (G=77GPa) are surrounded by the gears
shown. A torque T=340 N.m is applied at point A, determine:
1. The shear stress in shaft EC;
2. The angle through which end A rotates.
Homework Answers
Add Answer to:
The solid steel shafts (G=77GPa) are surrounded by the gears
shown. A torque T=340 N.m is...
P2. Two solid steel shafts, each of 30-mm diameter, are connected by the gears shown. Knowing...
P2. Two solid steel shafts, each of 30-mm diameter, are connected by the gears shown. Knowing that G- 77.2 GPa, determine the angle through which end A rotates when a torque of magnitude T= 200 N.m is applied at A. 0.2 m 30 mm 0.4 m 0.2m 60 mm 0.1m 90 mm 30 mm 0.5 m
Required information Two solid steel shafts are connected by the gears shown. A torque of magnitude...
Required information Two solid steel shafts are connected by the gears shown. A torque of magnitude T = 960 N.m is applied to shaft AB. The allowable shearing stress is 50 MPa. 240 mm 80 mm Considering only stresses due to twisting, determine the required diameter of shaft CD. The diameter of shaft CD is mm.
Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm...
Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm. Assume that the bearings shown allow free rotation of the shafts. If a 400 N-m torque is applied at gear D, determine (a) the maximum shear stress magnitudes in each shaft. (b) the angles of twist ф, and ф (c) the...
75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter...
75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter shafts are coupled together using the perfectly meshed gears shown. Shaft DC is fixed to the wall at D and supported with a frictionless journal bearing. Shaft EF is supported with two frictionless journal bearings. The modulus of rigidity of steel is 80 GPa. Before the torque is applied, the angle of twist in each shaft is zero, and the angle of rotation of...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks] a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
Ends A and D of the two solid steel shafts AB and CD are fixed, while ends B and C are connected...
Ends A and D of the two solid steel shafts AB and CD are fixed, while ends B and C are connected to gears as shown. Knowing that a 4kN-m torque T is applied to gear B,determine the maximum shearing stress (a) in shaft AB, (b) in shaft CD.
The splined ends and gears attached to the A992 steel shaft are subjected to the torques...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks) a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
P6.18 The gear train system shown in Figure P6.18/19 includes shafts (1) and (2), which are...
P6.18 The gear train system shown in Figure P6.18/19 includes shafts (1) and (2), which are solid 15 mm diameter steel shafts. The allowable shear stress of each shaft is 85 MPa. The diameter of gear B is Ds 200 mm, and the diameter of gear C is Dc 150 mm. The bearings shown allow the shafts to rotate freely. Determine the maximum torque TD that can be applied to the system without exceeding the allowable shear stress in either...
(2) The shaft is made from a solid steel section AB and a tubular portion made...
(2) The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T= 50 N.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gsi = 75 GPa, Ghr = 37.5 GPa. 800...
Question 1 The motor shown in Fig. 1 supplies power to Gear C through solid steel...
Question 1 The motor shown in Fig. 1 supplies power to Gear C through solid steel motor shaft GF (having a diamet of 200 mm) and Gear F. The torque delivered to Gear C is 200 kNm. Gears A, B, D and E supply powers to er three machines. The torques delivered by gear A, gear B and gear E to the machines are 60 kNm, 30 kNm and 40 kNm, respectively. Shaft ABCDE is also made of steel (G...
P2. Two solid steel shafts, each of 30-mm diameter, are connected by the gears shown. Knowing that G- 77.2 GPa, determine the angle through which end A rotates when a torque of magnitude T= 200 N.m is applied at A. 0.2 m 30 mm 0.4 m 0.2m 60 mm 0.1m 90 mm 30 mm 0.5 m
Required information Two solid steel shafts are connected by the gears shown. A torque of magnitude T = 960 N.m is applied to shaft AB. The allowable shearing stress is 50 MPa. 240 mm 80 mm Considering only stresses due to twisting, determine the required diameter of shaft CD. The diameter of shaft CD is mm.
Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm. Assume that the bearings shown allow free rotation of the shafts. If a 400 N-m torque is applied at gear D, determine (a) the maximum shear stress magnitudes in each shaft. (b) the angles of twist ф, and ф (c) the...
75 mm 1.5 m T = 48 N·m 2 m 150 mm Two solid steel 20-mm-diameter shafts are coupled together using the perfectly meshed gears shown. Shaft DC is fixed to the wall at D and supported with a frictionless journal bearing. Shaft EF is supported with two frictionless journal bearings. The modulus of rigidity of steel is 80 GPa. Before the torque is applied, the angle of twist in each shaft is zero, and the angle of rotation of...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks] a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks) a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
P6.18 The gear train system shown in Figure P6.18/19 includes shafts (1) and (2), which are solid 15 mm diameter steel shafts. The allowable shear stress of each shaft is 85 MPa. The diameter of gear B is Ds 200 mm, and the diameter of gear C is Dc 150 mm. The bearings shown allow the shafts to rotate freely. Determine the maximum torque TD that can be applied to the system without exceeding the allowable shear stress in either...
(2) The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T= 50 N.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gsi = 75 GPa, Ghr = 37.5 GPa. 800...
Question 1 The motor shown in Fig. 1 supplies power to Gear C through solid steel motor shaft GF (having a diamet of 200 mm) and Gear F. The torque delivered to Gear C is 200 kNm. Gears A, B, D and E supply powers to er three machines. The torques delivered by gear A, gear B and gear E to the machines are 60 kNm, 30 kNm and 40 kNm, respectively. Shaft ABCDE is also made of steel (G...
Most questions answered within 3 hours.
-
Suppose that on a temperature scale X, water boils at 203.0°X
and freezes at -105.7°X. What...
asked 8 minutes ago -
BaS crystallizes in a cubic unit cell with S2- ions on each
corner and each face....
asked 39 minutes ago -
A. 0≤P(Oi)≤10≤P(Oi)≤1 for each i
B. P(Oi)≤0P(Oi)≤0
C. P(Oi)=1+P(OCi)P(Oi)=1+P(OiC)
D. P(Oi)≥1P(Oi)≥1
If an experiment consists of...
asked 2 hours ago -
A battery has an emf of 9.20V and an internal resistance of 1.20
ohm. a)What resistance...
asked 2 hours ago -
The area of an elastic circular loop decreases at a constant
rate, dA/dt = −6.60×10−3 m2/s...
asked 3 hours ago -
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 4 hours ago -
Please answer what the maximum and minimum force is, and the
angle on the ion is...
asked 4 hours ago -
implement a program that reads a number of rows and a symbol.
The program will draw...
asked 4 hours ago -
Assume that when adults with smartphones are randomly selected,
45% use them in meetings or classes....
asked 5 hours ago -
Determine the number of formula units of
Na2SO4 and moles of oxygen contained in 8.11
moles...
asked 5 hours ago -
Explain in steps on the following code
What would be the output when executed
using System;...
asked 5 hours ago -
Given the information in the table, which of the following
statements is CORRECT?
Stock A
Stock...
asked 5 hours ago