2. A circular drum of radius R 1 ft without a top lid is filled with...
A water tank is shaped like a right, circular cylinder with height 6 ft and radius 3 ft. If the tank is filled to 1 ft below the top, find the work required to pump all of the water to the level of the top and let flow over the edge. The density of water is 62.5 lbs per cubic foot.
Pumping a conical tank A right- circular conical tank, point
down, with top radius 5 ft and height 10 ft is filled with a liquid
whose weight-density is 60 lb/ft^ 3 . How much work does it take to
pump the liquid to a point 2 ft above the tank? If the pump is
driven by a motor rated at 275 ft-lb/sec (1/2 hp), , how long will
it take to empty the tank? Must work the integral out by...
A crude oil storage tank in the shape of a right cylinder of radius 4 ft and length 10 ft is buried in the ground in the horizontal position. If the top of the tank is 5 ft below the surface, find the work required to empty a full tank of oil weighing 50 lb/ft' by pumping it though a pipe that extends to a height of 2 ft above the ground. You only need to set-up the integral. (Assume...
1. The armature of an ac generator is a circular coil with 292
turns and radius 4.6 cm. When the armature rotates at 939 rpm, the
amplitude of the emf in the coil is 21.3 V. What is the strength of
the magnetic field (assumed to be uniform)?
2. The armature of an ac generator is a rectangular coil 27.0 cm
by 17.9 cm with 294 turns. It is immersed in a uniform magnetic
field of magnitude 3.0 T. If...
Problem 5 (15 points) A small bead can slide without friction on a circular hoop that is a vertical plane and has a radius of 0.100 m. The hoop rotates at a constant rate of 4.00 rev/sec (recall 1 rev = 2π rad) about a vertical diameter as shown in the figure below (a) Find the angle β at which the bead is in vertical equilibrium. (It has a radial acceleration toward the axis.) (b) Is it possible for the...
e susJrom rest at the top of the well and falls for before hitting the water, how far does it fall? Moment of inertia of cylinder 1-% MR 2. A ladder is leant against the wall. The coefficient of the static friction p. between the ladder and the wall is 0.3 and the coefficient of the static friction g, between the ladder and the floor is 0.4. The center of mass of the ladder is in the middle of it...
TR PROBLEMS: Show your 1. A 1800 Kg car moves around a flat circular road of radius R- 100 m friction available between the tire and the road is 10368 N. Calculate (A) car can have so that it does not get out of the curve (B) the time alLoroblems radius R-100 m. The maximum amount ef (C) the new radius of the bigger circle the car moves on if it moves at a higher s the maxinmum speed the...
Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 800°C and 100°C, respectively. Determine the rate of heal transfer by radiation between the plates in Wim and the radiative heat transfer coefficient in W/m K ) 12 Write down the one-dimensional sent heal conduction equation for a plane wall with constant thermal conductivity and heat generation in its simplest form, and indicate what each variable represents 13 Write down the one-dimensional transient heat conduction...
5:16 lLTE ) Done 1 of 5 Assessment #1 (Kinematics of a Particle) Rectilinear Motion (Straight linc Motion 3. The position of a point during the interval of time from r otor 6 is given by ** * m. (a) What is the maximum velocity during this interval of time, and at what time does it occur? (b) What is the acceleration when the velocity is a maximum? (20 m/s, 0 m/s 3. A test projectile is fired horizontally into...
I need help to write a nice introduction for experiment 6
please ( no hands write ) typing
Thank you
HEAT TREATMENT OF STEELS EXPERIMENT 6 EXPERIMENT 6 HEAT TREATMENT OF STEELS THEORY The Effect of Cooling Rate One of the most convenient methods for controlling the properties of a given steel, i.e., a steel whose composition is already fixed, consists of austenizing the steel and ten cooling to room temperature at some predetermined rate. A variation of cooling rates...