Please show all work, will rate immediately ?? An Input noise Process nilt) having a PSD...
Will rate, answer quickly An input noise process n;(t) having a PSD that is constant between 200 and 700 rad/s (the power density is 10-W/Hz in the passband 200 to 700 rad/s) is the input to a lowpass filter whose bandwidth is 500 rad/sec and gain is 1. Do not forget that the spectrum and the frequency response are symmetrical between-co and +00. Sketch the PSD of noſt), the noise process at the output of the lowpass filter. Show all...
Answer quickly An input noise process n;(t) having a PSD that is constant between 200 and 700 rad/s (the power density is 10-W/Hz in the passband 200 to 700 rad/s) is the input to a lowpass filter whose bandwidth is 500 rad/sec and gain is 1. Do not forget that the spectrum and the frequency response are symmetrical between-co and +00. Sketch the PSD of noſt), the noise process at the output of the lowpass filter. Show all relevant details...
An input noise process n;(t) having a PSD that is constant between 200 and 700 rad/s (the power density is 106W/Hz in the passband 200 to 700 rad/s) is the input to a lowpass filter whose bandwidth is 500 rad/sec and gain is 1. Do not forget that the spectrum and the frequency response are symmetrical between-oo and +00. Sketch the PSD of noſt), the noise process at the output of the lowpass filter. Show all relevant details Find the...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandwidth 5 kHz, the receiver output SNR is required to be at least 47 dB. The receiver is as shown in Fig. 8.30. (a) What must be the signal power Si received at the receiver input? (b) What is the receiver output noise power No? (c) What is the minimum transmitted power Sr if the channel transfer function is He)10-3 over...
4) Let W(t) be AWGN. a) Sketch the PSD of W(t) You can use No to indicate amplitude in your sketch (i.e., no need to replace with the actual value). b) What is the power of W(t)? Assume Wlt) is the input to a lowpass filter with response given on the side and let N(t) beH(f)I the output of the filter. c) Sketch the PSD of N(t) Indicate amplitude of PSD and frequency points 300 300 (Hz) You can use...
Q.2 ICO2]10 Marks] The signal g(t) forms the input to the LPF circuit shown in the figure, where R l,and y(Dis the output. If the power spectral density (PSD) of the signal ge) is (a) The autocorrelation of g(t) (b) The 3-dB bandwidth of the LPF (c) The power of g(t) and y(t) (d) Based on your answers above, will it be better if the signal has more or less bandwith? (e) If a white noise of PSD No/2 is...
Consider additive white Gaussian noise with a double-sided noise power spectral density (PSD) 12-90 dBm/Hz 1E-12 W/Hz. This noise corrupts a baseband polar NRZ signal with rectangular pulses, like that 1 mV and the pulse duration is Tb such that the symbol rate is Rb 1/Tb. Since this is binary signaling, the symbol rate equals the bit rate of the incoming baseband pulse train: B Rt. The signal is then sampled at the center of the noisy shown in the...
Q1. A DSB-SC signal is transmitted over a noisy channel with power spectral density of noise given as, 0, otherwise with B-200 kHz and N 10W Hz. The message bandwidth is 10 kHz and its average power is 10 W. Assume A,-1, 100kHz, and the channel attenuates signal power by a factor of 1000 (-30 dB). Assume that a suitable band-pass filter is used at the receiver to limit out-of-band noise. (a) Determine the average signal power at the receiver...
b) Repeat part (a) if the reeelvel Wlll 10-7e-lala W/Hz, where 5.6.1 A noise waveform with a power spectral density S,(a) a 2T x 10'/sec, is passed through an ideal BPF with unity gain, unity resistane levels, and a bandwidth of 200 kHz centered at 10 MHz. a) Determine the mean-square values of the in-phase and quadrature components of the bandpass time representation given in Eq. (5.59). b) Repeat part (a) assuming that S,() is constant (at the center fre...
Q1) Let X(t) be a zero-mean WSS process with X(t) is input to an LTI system with Let Y(t) be the output. a) Find the mean of Y(t) b) Find the PSD of the output SY(f) c) Find RY(0) ------------------------------------------------------------------------------------------------------------------------- Q2) The random process X(t) is called a white Gaussian noise process if X(t) is a stationary Gaussian random process with zero mean, and flat power spectral density, Let X(t) be a white Gaussian noise process that is input to...