Homework Answers
Add Answer to:
2. A singly reinforced rectangular section having a cross-section b 300 mm and d = 600...
2. A rectangular beam, 400 x 600 mm gross dimension, is cast using a concrete strength...
2. A rectangular beam, 400 x 600 mm gross dimension, is cast using a concrete strength of fc 30 MPa, reinforced with 5-25 mm diameter steel bar at the effective depth of 500 mm. If is subjected to a moment, M 130 kN-m. Determine the following: Magnitude of the bending moment that cracks the singly-reinforced beam section. (10 pts) b. For the computed cracking moment, determine the maximum compressive stress in the concrete and the stress in the tension steel....
2.4 A rectangular reinforced concrete beam 300 x 550 mm (b x d) is provided with...
2.4 A rectangular reinforced concrete beam 300 x 550 mm (b x d) is provided with 4H20 bars as compression steel. Determine the area of tension steel needed for the beam to attain its full moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2 and fyk = 500 N/mm2.
A column 400 mm × 400 mm cross-section is reinforced with 4N32 bars and R10ties@160c/c. N32 concrete is used. A cover of 20 mm is provided. The column is subjected to an axial force of 600kN and a ben...
A column 400 mm × 400 mm cross-section is reinforced with 4N32 bars and R10ties@160c/c. N32 concrete is used. A cover of 20 mm is provided. The column is subjected to an axial force of 600kN and a bending moment of 300 kN.m. The column is pinned at the bottom and is restricted at the top. The length of the column is 4.0 m. Check if the reinforcement provided is OK and if not re-design the column.
Q:A beam section having b × D= 400 mm × 800 mm is required to develop...
Q:A beam section having b × D= 400 mm × 800 mm is required to develop an effective ultimate moment (M,) of 1800 kNm. Design the reinforcement using compression steel if necessary 8, Assume = 32 MPa and fy = 500 MPa. Sketch the cross-section showing the rein- forcement details. Use N36 bars only with R10 ties. Exposure classification A2 applies.
FIGURE Q2 shows cross-section of a rectangular doubly reinforced concrete beam. The concrete grade, fck is...
FIGURE Q2 shows cross-section of a rectangular doubly reinforced concrete beam. The concrete grade, fck is 20 N/mm2 and the steel grade, fyk is 500 N/mm2. Evaluate whether the beam has been designed as under reinforced section AND also determine if the section is able to resist an applied moment of 75 kN.m. [10 marks] 30 mm T 3H10 300 mm 5H12 30 mm 100 mm FIGURE Q2
Task 1: (50 Marks) Cross section of a reinforced concrete beam is shown in Figure 1....
Task 1: (50 Marks) Cross section of a reinforced concrete beam is shown in Figure 1. The following shear forces have been calculated due to Dead Load and Live Load at the support: VDL = 150 kN, ViL = 200 kN. Design the shear reinforcement for the ultimate shear force. Use No. 10 bars for shear reinforcement Assume "fe, = 28 MPa, fyt-420 MPa, b = 300 mm, d = 750 mm, h = 800 mm Figure 1. Beam cross-section
ACI code Interaction Diagrams and Strain Compatibility for Columns The column cross-section is 300 mm x...
ACI code
Interaction Diagrams and Strain Compatibility for Columns The column cross-section is 300 mm x 500 mm and is not in contact with the ground or exposed to the weather. Ties are #10 bars and longitudinal reinforcement is # 19. Concrete compressive strength is 42 MPa and steel yield strength is 420 MPa. Calculate the axial load carrying capacity, OP and flexural capacity OM, for point in the interaction diagram with bending about the 3-3 axis where the tensile...
8-7 A rectangular beam with cross section b h=24 in., and d tored load of 3.9...
8-7 A rectangular beam with cross section b h=24 in., and d tored load of 3.9 kips/ft, including its own dead load. The beam is simply supported with a is reinforced with five No. 7 Grade-60 bars, two of which are cutoff between midspan and the and three of which extend 10 in. past the centers of supports. f= 4000 psi. (normal weight). The beam has Grade 60 No. 3 stirrups satisfying AC Code Sections 9.7.6.2.2 and 9.6.3.3. 14 in.,...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD=500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fe 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two layers), 26...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
2. A rectangular beam, 400 x 600 mm gross dimension, is cast using a concrete strength of fc 30 MPa, reinforced with 5-25 mm diameter steel bar at the effective depth of 500 mm. If is subjected to a moment, M 130 kN-m. Determine the following: Magnitude of the bending moment that cracks the singly-reinforced beam section. (10 pts) b. For the computed cracking moment, determine the maximum compressive stress in the concrete and the stress in the tension steel....
2.4 A rectangular reinforced concrete beam 300 x 550 mm (b x d) is provided with 4H20 bars as compression steel. Determine the area of tension steel needed for the beam to attain its full moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2 and fyk = 500 N/mm2.
FIGURE Q2 shows cross-section of a rectangular doubly reinforced concrete beam. The concrete grade, fck is 20 N/mm2 and the steel grade, fyk is 500 N/mm2. Evaluate whether the beam has been designed as under reinforced section AND also determine if the section is able to resist an applied moment of 75 kN.m. [10 marks] 30 mm T 3H10 300 mm 5H12 30 mm 100 mm FIGURE Q2
Task 1: (50 Marks) Cross section of a reinforced concrete beam is shown in Figure 1. The following shear forces have been calculated due to Dead Load and Live Load at the support: VDL = 150 kN, ViL = 200 kN. Design the shear reinforcement for the ultimate shear force. Use No. 10 bars for shear reinforcement Assume "fe, = 28 MPa, fyt-420 MPa, b = 300 mm, d = 750 mm, h = 800 mm Figure 1. Beam cross-section
ACI code
Interaction Diagrams and Strain Compatibility for Columns The column cross-section is 300 mm x 500 mm and is not in contact with the ground or exposed to the weather. Ties are #10 bars and longitudinal reinforcement is # 19. Concrete compressive strength is 42 MPa and steel yield strength is 420 MPa. Calculate the axial load carrying capacity, OP and flexural capacity OM, for point in the interaction diagram with bending about the 3-3 axis where the tensile...
8-7 A rectangular beam with cross section b h=24 in., and d tored load of 3.9 kips/ft, including its own dead load. The beam is simply supported with a is reinforced with five No. 7 Grade-60 bars, two of which are cutoff between midspan and the and three of which extend 10 in. past the centers of supports. f= 4000 psi. (normal weight). The beam has Grade 60 No. 3 stirrups satisfying AC Code Sections 9.7.6.2.2 and 9.6.3.3. 14 in.,...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD=500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fe 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two layers), 26...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
Most questions answered within 3 hours.
-
Which statement is always true: The total energy of a closed
system...
A) is always equally...
asked 9 minutes ago -
find the critical value associated with a right sided hypothesis of
the mean using a sample...
asked 2 hours ago -
Which of the following statements is true with respect to a
simple linear regression model?
a....
asked 2 hours ago -
The energy required to remove an electron from a surface of a
solid element is called...
asked 4 hours ago -
How would you train your employees to avoid risks of using
mobile devices?
asked 4 hours ago -
Assume Kw = 1.01 ✕ 10−14
For pure water, we can calculate [H3O+ ] = [OH...
asked 5 hours ago -
Suppose that on a temperature scale X, water boils at 203.0°X
and freezes at -105.7°X. What...
asked 6 hours ago -
BaS crystallizes in a cubic unit cell with S2- ions on each
corner and each face....
asked 6 hours ago -
A. 0≤P(Oi)≤10≤P(Oi)≤1 for each i
B. P(Oi)≤0P(Oi)≤0
C. P(Oi)=1+P(OCi)P(Oi)=1+P(OiC)
D. P(Oi)≥1P(Oi)≥1
If an experiment consists of...
asked 8 hours ago -
A battery has an emf of 9.20V and an internal resistance of 1.20
ohm. a)What resistance...
asked 8 hours ago -
The area of an elastic circular loop decreases at a constant
rate, dA/dt = −6.60×10−3 m2/s...
asked 9 hours ago -
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 11 hours ago