Homework Answers
Here it is the design of rectangular section Beam. And find that
as per given Information.
Add Answer to:
2. A rectangular beam, 400 x 600 mm gross dimension, is cast using a concrete strength...
A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth,...
A reinforced concrete beam has the following properties:
Beam width, b = 320 mm
Effective depth, d = 640 mm
Concrete strength, f’c = 21 MPa
Reinforcing steel strength, fy = 400 MPa
If the factored shear force at the critical section is 210,000 N,
compute the nominal shear carried
by the shear reinforcement.
EXERCISE - USD SHEAR 1. A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth, d = 640 mm Concrete...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD=500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fe 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two layers), 26...
Reinforced concrete Problem #1 (40 points): A beam with x-section shown in the figure is made...
Reinforced concrete
Problem #1 (40 points): A beam with x-section shown in the figure is made out of concrete with compressive strength fc = 4000 psi and the steel reinfrocemnt is of Grade 60 (fy 60000psi). Determine 1 The maximum compressive stress in the concrete f and the tensils stress in the steel , if the section is subjected to a bending moment of 130 ft-k (assume n 8) N.A._ 23" 23-х 4 #10 (5.06 in. 3" 18"
1. A cross section of a RC beam is described in a below figure. Three No....
1. A cross section of a RC beam is described in a below figure. Three No. 29 reinforcing bars are located at the bottom of the section. The area of a #29 reinforcing bar is 645 mm2 while the yield strength of the steel bar is 420 MPa. The tensile strength of concrete is 2.7 MPa, and the compressive strength of concrete is 21 MPa. In addition, n= E/Eis selected as 8. (1) Compute the maximum compressive and tensile stresses...
Problem 2 A reinforced concrete beam (see fig.) is acted on by a positive bending moment...
Problem 2 A reinforced concrete beam (see fig.) is acted on by a positive bending moment of M - 160 kNm. Steel reinforcement consists of 4 bars of 28-mm diameter. The modulus of elasticity for the concrete is E = 25 GPa while that of the steel is E, = 200 GPa. (a) Find the maximum stresses in steel and concrete. (b) If allowable stresses for concrete and steel are = 9.2 MPa and 0 -135 MPa, respectively, what is...
03(a) A reinforced concrete beam is acted on by a positive bending moment. reinforcement consists of 4 bars of 28 mm diameter. The modulus of elasticity is E 25 GPa for the concrete and E-200 G...
03(a) A reinforced concrete beam is acted on by a positive bending moment. reinforcement consists of 4 bars of 28 mm diameter. The modulus of elasticity is E 25 GPa for the concrete and E-200 GPa for the steel. The allowable stresses for the concrete and steel are ơ.-9.2 MPa and ơ.-135 MPa, respectively. Determine the maximum permissible positive bending moment. (10 marks) 625 mm 4 bars 28 mm -300 mm Figure Q3(a) 03(b) A simply supported beam that is...
reinforced concrete design , ACI code Shear Strength of Flexural Members Design for shear forces The...
reinforced concrete design , ACI code
Shear Strength of Flexural Members Design for shear forces The simply supported beam shown is subjected to ultimate (factored) distributed and concentrated loads 1. Determine the shear capacity of concrete at the critical section according to ACI318-14 detailed method in Table 22.5.5.1. Design the shear reinforcement and determine the locations on the beam shear force diagram where this shear reinforcement should be placed. 2. 3. Determine the locations within the beam where minimum shear...
131 The concrete beam is reinforced with three 20-mm- diameter steel rods. Assume that the concrete...
131 The concrete beam is reinforced with three 20-mm- diameter steel rods. Assume that the concrete cannot support tensile stress. If the allowable compressive stress for concrete is (allown2.5 MPa and the allowable tensile stress for steel is (?allow)st-220 MPa, determine the required dimension d so that both the concrete and steel achieve their allowable stress simultaneously. This condition is said to be 'balanced'. Also, compute the corresponding maximum allowable internal moment M that can be applied to the beam....
Problem 2. A concrete beam is reinforced by three steel rebars placed as shown. The modulus...
Problem 2. A concrete beam is reinforced by three steel rebars placed as shown. The modulus of elasticity is 3x106 psi for concrete and 29x106 psi for steel. Find the tensile stress in rebars and maximum compressive stress in concrete under an external bending moment of (a) 80 kip.in and (b) 240 kip.in. Given the compressive strength of concrete fe' = 3 ksi and yield stress of rebars fy = 60 ksi, discuss the state of crack in concrete and...
A reinforced concrete beam has the following properties:
Beam width, b = 320 mm
Effective depth, d = 640 mm
Concrete strength, f’c = 21 MPa
Reinforcing steel strength, fy = 400 MPa
If the factored shear force at the critical section is 210,000 N,
compute the nominal shear carried
by the shear reinforcement.
EXERCISE - USD SHEAR 1. A reinforced concrete beam has the following properties: Beam width, b = 320 mm Effective depth, d = 640 mm Concrete...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD=500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fe 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two layers), 26...
Reinforced concrete
Problem #1 (40 points): A beam with x-section shown in the figure is made out of concrete with compressive strength fc = 4000 psi and the steel reinfrocemnt is of Grade 60 (fy 60000psi). Determine 1 The maximum compressive stress in the concrete f and the tensils stress in the steel , if the section is subjected to a bending moment of 130 ft-k (assume n 8) N.A._ 23" 23-х 4 #10 (5.06 in. 3" 18"
1. A cross section of a RC beam is described in a below figure. Three No. 29 reinforcing bars are located at the bottom of the section. The area of a #29 reinforcing bar is 645 mm2 while the yield strength of the steel bar is 420 MPa. The tensile strength of concrete is 2.7 MPa, and the compressive strength of concrete is 21 MPa. In addition, n= E/Eis selected as 8. (1) Compute the maximum compressive and tensile stresses...
Problem 2 A reinforced concrete beam (see fig.) is acted on by a positive bending moment of M - 160 kNm. Steel reinforcement consists of 4 bars of 28-mm diameter. The modulus of elasticity for the concrete is E = 25 GPa while that of the steel is E, = 200 GPa. (a) Find the maximum stresses in steel and concrete. (b) If allowable stresses for concrete and steel are = 9.2 MPa and 0 -135 MPa, respectively, what is...
03(a) A reinforced concrete beam is acted on by a positive bending moment. reinforcement consists of 4 bars of 28 mm diameter. The modulus of elasticity is E 25 GPa for the concrete and E-200 GPa for the steel. The allowable stresses for the concrete and steel are ơ.-9.2 MPa and ơ.-135 MPa, respectively. Determine the maximum permissible positive bending moment. (10 marks) 625 mm 4 bars 28 mm -300 mm Figure Q3(a) 03(b) A simply supported beam that is...
reinforced concrete design , ACI code
Shear Strength of Flexural Members Design for shear forces The simply supported beam shown is subjected to ultimate (factored) distributed and concentrated loads 1. Determine the shear capacity of concrete at the critical section according to ACI318-14 detailed method in Table 22.5.5.1. Design the shear reinforcement and determine the locations on the beam shear force diagram where this shear reinforcement should be placed. 2. 3. Determine the locations within the beam where minimum shear...
131 The concrete beam is reinforced with three 20-mm- diameter steel rods. Assume that the concrete cannot support tensile stress. If the allowable compressive stress for concrete is (allown2.5 MPa and the allowable tensile stress for steel is (?allow)st-220 MPa, determine the required dimension d so that both the concrete and steel achieve their allowable stress simultaneously. This condition is said to be 'balanced'. Also, compute the corresponding maximum allowable internal moment M that can be applied to the beam....
Problem 2. A concrete beam is reinforced by three steel rebars placed as shown. The modulus of elasticity is 3x106 psi for concrete and 29x106 psi for steel. Find the tensile stress in rebars and maximum compressive stress in concrete under an external bending moment of (a) 80 kip.in and (b) 240 kip.in. Given the compressive strength of concrete fe' = 3 ksi and yield stress of rebars fy = 60 ksi, discuss the state of crack in concrete and...
Most questions answered within 3 hours.
-
. A 100.0 mL sample of 0.18 M HClO4 is titrated with 0.27 M
LiOH. Determine...
asked 10 minutes ago -
A regression equation that describes the relationship between
the amount of the bill ($) at a...
asked 1 hour ago -
exercise on VSEPR and molecular structrue.
octahedral
SeCl62-
TeCl62-
ClF62-
distorted
SeF62–
IF6–
asked 1 hour ago -
284 mL of a 0.52 M potassium hydroxide solution is added to 467
mL of a...
asked 1 hour ago -
Little’s Law: Val d’Costa is a world famous ski village in the
French Alps. Because of...
asked 2 hours ago -
Find the absolute error D for the calculation if A + B/C=D A=
9.4 +/- 0.4...
asked 2 hours ago -
New Air Heating and Cooling, manufactures furnaces and central
air units. The company pride itself on...
asked 2 hours ago -
A coach uses a new technique to train gymnasts. Seven
gymnasts were randomly selected and their...
asked 4 hours ago -
While rotating the tires on your car you notice a rock [mass =
0.1 Kg] stuck...
asked 6 hours ago -
Using MARS simulator, write MIPS programs according to
the following scenarios: Receive a positive integer number...
asked 8 hours ago -
An object in front of a concave mirror has a real image that is
11.5 cm...
asked 8 hours ago -
Consider the reaction, C3 H8 + O2 --> CO2 + H2O. How many
moles of O2...
asked 10 hours ago