Homework Answers
Add Answer to:
Reinforced concrete
Problem #1 (40 points): A beam with x-section shown in the figure is made...
2. A rectangular beam, 400 x 600 mm gross dimension, is cast using a concrete strength...
2. A rectangular beam, 400 x 600 mm gross dimension, is cast using a concrete strength of fc 30 MPa, reinforced with 5-25 mm diameter steel bar at the effective depth of 500 mm. If is subjected to a moment, M 130 kN-m. Determine the following: Magnitude of the bending moment that cracks the singly-reinforced beam section. (10 pts) b. For the computed cracking moment, determine the maximum compressive stress in the concrete and the stress in the tension steel....
Problem 2. A concrete beam is reinforced by three steel rebars placed as shown. The modulus...
Problem 2. A concrete beam is reinforced by three steel rebars placed as shown. The modulus of elasticity is 3x106 psi for concrete and 29x106 psi for steel. Find the tensile stress in rebars and maximum compressive stress in concrete under an external bending moment of (a) 80 kip.in and (b) 240 kip.in. Given the compressive strength of concrete fe' = 3 ksi and yield stress of rebars fy = 60 ksi, discuss the state of crack in concrete and...
1. Reinforced Rectangular Concrete Beam The reinforced concrete beam shown is subjected to a bending moment...
1. Reinforced Rectangular Concrete Beam The reinforced concrete beam shown is subjected to a bending moment of 200 kip ft. Knowing that the modulus of elasticity for the concrete and the steel are respectively Ec= 3.75 X 10 psi and Es = 30 x 10 psi, determine the tensile stress in [ksh] that develops in the steel bars. 20 in 1 in diameter 72.5 in 12 in-
In the following reinforced concrete beam, bending moment is 150kip-ft and Ec = 3.75x10^6psi Es =...
In the following reinforced concrete beam, bending moment is
150kip-ft and Ec = 3.75x10^6psi Es = 30x10^6psi determine (a) the
stress in the steel (b) the madimum stress in the concrete
This is what I've done so far. I think the next step is to
calculate the distance of neutral axis from the bottom section
which should end up in a quadratic equation to solve for x.
Q4) In the following reinforced concrete beam, bending moment is 150kip-ft and E=3.75x10°Es=30x10ʻpsi...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips at mid-point of the beam and a uniformly-distributed load of 4 kips/ft over the entire span. Given: (a) The breadth of the beam is 18 inches. (b) Concrete compressive strength, fc, is 3500 psi. (c) Rebar is Grade 40 steel i) Determine the maximum moment and maximum shear acting on the beam. ii) Determine the minimum effective depth 'd' of the beam section (rounded...
326 СНАРТER 6 BENDING EXAMPLE 6.18 The reinforced concrete beam has the cross-sectional area shown in Fig. 6-39a. If it...
326 СНАРТER 6 BENDING EXAMPLE 6.18 The reinforced concrete beam has the cross-sectional area shown in Fig. 6-39a. If it is subjected to a bending moment of M = 60 kip ft determine the normal stress in each of the steel reinforcing rods and the maximum normal stress in the concrete. Take Est = 29(10) ksi and Econc = 3.6(103) ksi SOLUTION Since the beam is made of concrete, in the following analysis we will neglect its strength in supporting...
Problem 2 Determine the nominal moment capacity for the reinforced concrete beam shown. The beam ...
Problem 2 Determine the nominal moment capacity for the reinforced concrete beam shown. The beam cross section has a width 10 inch and a depth 20 inch. The beam is reinforced with a tension steel reinforcement of 3#8 with an area of steel # 2.37 inch Assume grade 60 steel with a yield strss, Fy 60 ksi d 20 3#8 2.37/ 2 As B-10"
Problem 2 Determine the nominal moment capacity for the reinforced concrete beam shown. The beam cross...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
I designed and detailed the beam in problem 3 as you see. Redesign the reinforced concrete...
I designed and detailed the beam in problem 3 as you see.
Redesign the reinforced concrete beam of problem 3, If the value of
factored bending moment increased to 1,600 k.ft where the section
needs to be designed as a doubly reinforced beam.
3) Design and detail the reinforced concrete beam shown below if it is subjected to a factored bending moment of 1,100 k.ft f'=4,800psi fx=60 ksi. Include skin steel. 36" 15" 2#6 36 24 kino f's = 4800...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips at mid-point of the beam and a uniformly-distributed load of 4 kips/ft over the entire span. Given: (a) The breadth of the beam is 18 inches. (b) Concrete compressive strength, f 'c, is 3500 psi. (c) Rebar is Grade 40 steel i) Determine the maximum moment and maximum shear acting on the beam. ii) Determine the minimum effective depth 'd' of the beam section...
2. A rectangular beam, 400 x 600 mm gross dimension, is cast using a concrete strength of fc 30 MPa, reinforced with 5-25 mm diameter steel bar at the effective depth of 500 mm. If is subjected to a moment, M 130 kN-m. Determine the following: Magnitude of the bending moment that cracks the singly-reinforced beam section. (10 pts) b. For the computed cracking moment, determine the maximum compressive stress in the concrete and the stress in the tension steel....
Problem 2. A concrete beam is reinforced by three steel rebars placed as shown. The modulus of elasticity is 3x106 psi for concrete and 29x106 psi for steel. Find the tensile stress in rebars and maximum compressive stress in concrete under an external bending moment of (a) 80 kip.in and (b) 240 kip.in. Given the compressive strength of concrete fe' = 3 ksi and yield stress of rebars fy = 60 ksi, discuss the state of crack in concrete and...
1. Reinforced Rectangular Concrete Beam The reinforced concrete beam shown is subjected to a bending moment of 200 kip ft. Knowing that the modulus of elasticity for the concrete and the steel are respectively Ec= 3.75 X 10 psi and Es = 30 x 10 psi, determine the tensile stress in [ksh] that develops in the steel bars. 20 in 1 in diameter 72.5 in 12 in-
In the following reinforced concrete beam, bending moment is
150kip-ft and Ec = 3.75x10^6psi Es = 30x10^6psi determine (a) the
stress in the steel (b) the madimum stress in the concrete
This is what I've done so far. I think the next step is to
calculate the distance of neutral axis from the bottom section
which should end up in a quadratic equation to solve for x.
Q4) In the following reinforced concrete beam, bending moment is 150kip-ft and E=3.75x10°Es=30x10ʻpsi...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips at mid-point of the beam and a uniformly-distributed load of 4 kips/ft over the entire span. Given: (a) The breadth of the beam is 18 inches. (b) Concrete compressive strength, fc, is 3500 psi. (c) Rebar is Grade 40 steel i) Determine the maximum moment and maximum shear acting on the beam. ii) Determine the minimum effective depth 'd' of the beam section (rounded...
326 СНАРТER 6 BENDING EXAMPLE 6.18 The reinforced concrete beam has the cross-sectional area shown in Fig. 6-39a. If it is subjected to a bending moment of M = 60 kip ft determine the normal stress in each of the steel reinforcing rods and the maximum normal stress in the concrete. Take Est = 29(10) ksi and Econc = 3.6(103) ksi SOLUTION Since the beam is made of concrete, in the following analysis we will neglect its strength in supporting...
Problem 2 Determine the nominal moment capacity for the reinforced concrete beam shown. The beam cross section has a width 10 inch and a depth 20 inch. The beam is reinforced with a tension steel reinforcement of 3#8 with an area of steel # 2.37 inch Assume grade 60 steel with a yield strss, Fy 60 ksi d 20 3#8 2.37/ 2 As B-10"
Problem 2 Determine the nominal moment capacity for the reinforced concrete beam shown. The beam cross...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
I designed and detailed the beam in problem 3 as you see.
Redesign the reinforced concrete beam of problem 3, If the value of
factored bending moment increased to 1,600 k.ft where the section
needs to be designed as a doubly reinforced beam.
3) Design and detail the reinforced concrete beam shown below if it is subjected to a factored bending moment of 1,100 k.ft f'=4,800psi fx=60 ksi. Include skin steel. 36" 15" 2#6 36 24 kino f's = 4800...
Most questions answered within 3 hours.
-
A .15kg rubber ball is bounced off a wall. Before hitting the
wall, the ball moves...
asked 8 minutes ago -
A manufacturing company preparing to build a new plant is
considering three potential locations for it....
asked 9 minutes ago -
B. If compound Y has approximately the same values of solubility
in toluene as compound X,...
asked 56 minutes ago -
Oscar Inc. has inventory in Japan valued at 39,051,000 Yen one
year ago. One year ago...
asked 1 hour ago -
If Canada suffered from "fundamental disequilibrium," and its
government choose not to devalue its currency, a...
asked 1 hour ago -
4. How many input & output Key Value Pairs are passed into,
and emitted out of...
asked 1 hour ago -
Why would your heart not function well if constructed of
skeletal muscle? What is the particular...
asked 1 hour ago -
Please respond to this essay question in full essay form for
Chemistry 1102 Organic and Biochemistry:...
asked 1 hour ago -
Determine the head loss and velocity of flow in a water supply main
of 15.0 cm...
asked 1 hour ago -
A marketing executive who knowingly authorizes a shoddy
defective product to be brought to market is...
asked 1 hour ago -
Write a psudocode:
1. Define a function called authorize that takes in 2 strings,
uName, and...
asked 1 hour ago -
What Hall voltage (in mV) is produced by a 0.180 T field applied
across a 2.60...
asked 1 hour ago