Please draw the front , right, and top view of the object in the third line...
Please draw the front , right, and top view of the object in the third line and show construction lines, central line and hidden line .show the size please 2X 0.63- 200 3.29 1.00 1.00 - 2X 0.75 AD 1.75 1.00 200 200 1.75 3.25 1-83 200 0 1.75 FILLETS & ROUNDS R.13 sronor NLNE ARM 2X9X2 X2 15 R12 50 $12 x 4 HOLES RIZ 62 23 60 110 45
Please draw the front , right, and top view of the object in the third line and show construction lines, central line and hidden line . show all sizes ( plz draw 2 photos) 050 430 50 -15 2 holes R15 59 26 60 R7.50 50.50 12.30 21.6 5 13:00 400 5.00 10.00 935 -12.00 5.00 T 18.50 25.00
Please draw the front , right, and top view of the object in the third line and show construction lines, central line and hidden line . show the size plz. of 3 drawing. R7.50 50.50 12.30 21.6 5 13:00 400 5.00 10.00 935 -12.00 5.00 T 18.50 25.00 050 430 50 -15 2 holes R15 59 26 60 -30 -60 pant 50 40 15R SER 215 15 4 holes! 170 -70
I need the front view, top view, and right side view of this object. Please and Thank you!!! R1.50 RI.00 1,00 5.00 Rounds & Fillets: R.25 1.00 aft Support (Dimensions are in Millimeters. Note the two R40 arcs at the base share the same center.)
Draw the front, top, right side view and section view, and Isometric view. Use half section view. - FILLETS AND ROUNDS R.12 Ø5.501 s 02.75 L4X 05 1.498-1.500 Figure 8.5: Bearing.
following object converting the front view into a full section. Draw the Min plane line. It is not necessary to include the dimensions. The matera Chapter 5: Sectioning 1 25-30) Draw the fo propriate cutting the part is Cast Iron - 6.50 02.00 7.75 1.50 .75 full section View 1.50 Seprate sheet NOTE: ALL ROUNDS AND FILLETS 12 R
PLEASE DRAW THIS IN AUTOCAD TOP FRONT AND RIGHT SIDE VIEWS INCLUDE HIDDEN AND CENTER LINES 8. Below 1.00 1.50 0.75 2.50 2 x 0.50- 1.50
Top view Front view. Right view No required scale Activity 4: Draw an isometric pictorial from the given top, front and right side view of an object. Use your engineer's pad to complete this activity. Use dimensions for proportions only .75 1.00 .75 1.00 .50 .62 25
Given: The front and top views of an object. Required: Draw the right side view and complete the bottom half as instructed. For part 2: Draw the right side view of surface 14,17,19,20,26. ORTHOGRAPHIC READING GIVEN: The front and top views of an object. 10 REQUIRED: Draw the right side view and complete the bottom half as instructed. 13 14 15 16 17 18. 26 20 22 Draw the right side view of surface 14,17,19,20,26. 14 26
Draw the top, front and right view for each of the following problems. Make sure you draw the views in the correct locations, and at the right orientations. Draw all the construction lines and the miter lines. Use a ruler. Professional work please.