I need the front view, top view, and right side view of this object. Please and Thank you!!!
I need the front view, top view, and right side view of this object. Please and...
Please draw the front , right, and top view of the object in
the third line and show construction lines, central line and hidden
line . show all sizes plz .
2X 0.63- 200 3.29 1.00 1.00 - 2X 0.75 AD 1.75 1.00 200 200 1.75 3.25 1-83 200 0 1.75 FILLETS & ROUNDS R.13
Please draw the front , right, and top view of the object in
the third line and show construction lines, central line and hidden
line .show the size please
2X 0.63- 200 3.29 1.00 1.00 - 2X 0.75 AD 1.75 1.00 200 200 1.75 3.25 1-83 200 0 1.75 FILLETS & ROUNDS R.13 sronor NLNE ARM 2X9X2 X2 15 R12 50 $12 x 4 HOLES RIZ 62 23 60 110 45
Draw the front, top, right side view and section view, and
Isometric view. Use half section view.
- FILLETS AND ROUNDS R.12 Ø5.501 s 02.75 L4X 05 1.498-1.500 Figure 8.5: Bearing.
Top view
Front view. Right view
No required scale
Activity 4: Draw an isometric pictorial from the given top, front and right side view of an object. Use your engineer's pad to complete this activity. Use dimensions for proportions only .75 1.00 .75 1.00 .50 .62 25
Given: The front and top views of an object.
Required: Draw the right side view and complete the bottom half
as instructed.
For part 2: Draw the right side view of surface
14,17,19,20,26.
ORTHOGRAPHIC READING GIVEN: The front and top views of an object. 10 REQUIRED: Draw the right side view and complete the bottom half as instructed. 13 14 15 16 17 18. 26 20 22 Draw the right side view of surface 14,17,19,20,26. 14 26
Please draw the front , right, and top view of the object in
the third line and show construction lines, central line and hidden
line . show all sizes ( plz draw 2 photos)
050 430 50 -15 2 holes R15 59 26 60 R7.50 50.50 12.30 21.6 5 13:00 400 5.00 10.00 935 -12.00 5.00 T 18.50 25.00
Please draw the front , right, and top view of the object in the
third line and show construction lines, central line and hidden
line . show the size plz. of 3 drawing.
R7.50 50.50 12.30 21.6 5 13:00 400 5.00 10.00 935 -12.00 5.00 T 18.50 25.00 050 430 50 -15 2 holes R15 59 26 60 -30 -60 pant 50 40 15R SER 215 15 4 holes! 170 -70
following object converting the front view into a full section. Draw the Min plane line. It is not necessary to include the dimensions. The matera Chapter 5: Sectioning 1 25-30) Draw the fo propriate cutting the part is Cast Iron - 6.50 02.00 7.75 1.50 .75 full section View 1.50 Seprate sheet NOTE: ALL ROUNDS AND FILLETS 12 R
sketch an isometric view given top front and right
views.
ㄚ Top, Front & the side views are given. Sketch an isometric view.
please use the graphic paper
Sketch the ISOMETRIC view of the object. The given TOP, FRONT and RIGHT SIDE views are complete. Use point "O" for orientation. TOP RIGHT SIDE FRONT