Homework Answers
Add Answer to:
A buck converter is used to have low output voltage from the high input source to...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage 12 V. Switching frequency is 15 kHz. Calculate duty ratios for the switch and the diode. Find values for the inductor L and capacitor C, when the allowed output voltage ripple is ±0.15 % and the inductor current ripple is ±1 % (of the average value). If the on-time of the switch has an inaccuracy of ±50 ns, what is the new output voltage...
Design a buck converter with the following specifications: Input voltage = 311 V Output voltage =...
Design a buck converter with the following specifications: Input voltage = 311 V Output voltage = 48 V Output voltage ripple = +/- 0.1% Maximum output current = 10 A Inductor current ripple = 5% Switching frequency = 100 kHz a) Select the inductor and the output capacitor and show a capture of the behaviour b) Calculate power losses assuming a rising time of 100 ns, a falling time of 100 ns, and Rdson = 10 mΩ. c) Calculate output...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Buck Converter Question Q3. A Buck converter is used to produce a regulated 10V, 5A DC...
Buck Converter Question
Q3. A Buck converter is used to produce a regulated 10V, 5A DC power supply from a variable DC source with an nominal input voltage of Vin = 20V±5V. The Buck converter switches at 250kHz, and operates entirely in the continuous conduction mode. The output filter capacitance is C1.0uF 3.a. Draw the circuit topology for the Buck converter. Ensure that your circuit includes the input DC source, the output load resistance, the switching devices (i.e. MOSFET and...
Design a buck converter which has an output of 12V from an input of 18V. The...
Design a buck converter which has an output of 12V from an input of 18V. The output power is 10W. The output voltage ripple must be no more than 100mV peak to peak. Specify the duty ratio, switching frequency is 500kHz, ton, and inductor and capacitor values. Design for continuous inductor current. Assume ideal conditions, and assume the output current is symmetric
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 ...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
In the following buck converter, let the switching frequency be 50 kHz. Determine if the converter...
In the following buck converter, let the switching frequency be 50 kHz. Determine if the converter is in CCM or DCM Compute the average inductor current, peak-peak current ripple Average transistor current, average diode current Peak current in the transistor Peak-peak ripple in the output voltage f.Power delivered by the input 12V source Vd=12 ,Vo=8V ,R=4ohm, L=20uH ,C=50uF
In the following buck converter, let the switching frequency be 50 kHz. Determine if the converter is in CCM or DCM ...
In the following buck converter, let the switching frequency be 50 kHz. Determine if the converter is in CCM or DCM Compute the average inductor current, peak-peak current ripple Average transistor current, average diode current Peak current in the transistor Peak-peak ripple in the output voltage f.Power delivered by the input 12V source Vd=12 ,Vo=8V ,R=4ohm, L=20uH ,C=50uF
To design a high efficiency d.c., to d.c power converter with the given specifications min 10V max 15V nominal (regulated) 8V Input voltage: Output voltage: Nominal load current: 4A Inductor current...
To design a high efficiency d.c., to d.c power converter with the given specifications min 10V max 15V nominal (regulated) 8V Input voltage: Output voltage: Nominal load current: 4A Inductor current ripple: 0.1A max Switching frequency: 30 kHz Output voltage ripple: 20 mV Define a suitable power circuit topology to meet the above specification? Sketch a circuit diagram of the chosen power circuit topology (a) Define the minimum and maximum duty cycles assuming that the control circuit keeps the output...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage ripple:max 20mV Load power: Switching frequency: 15kHz 110-125V 300V 1.5kW Calculate: (i) Maximum duty cycle (ii) Minimum duty cycle (iii) Average diode current (iv) Assuming the Rds(on) of the MOSFET is 0.01 Ω, and the diode forward voltage is 0.8V, calculate the approximate efficiency of the circuit. 2. A switching power supply shown in the circuit below has its switch driven by a signal...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Buck Converter Question
Q3. A Buck converter is used to produce a regulated 10V, 5A DC power supply from a variable DC source with an nominal input voltage of Vin = 20V±5V. The Buck converter switches at 250kHz, and operates entirely in the continuous conduction mode. The output filter capacitance is C1.0uF 3.a. Draw the circuit topology for the Buck converter. Ensure that your circuit includes the input DC source, the output load resistance, the switching devices (i.e. MOSFET and...
Design a buck converter which has an output of 12V from an input of 18V. The output power is 10W. The output voltage ripple must be no more than 100mV peak to peak. Specify the duty ratio, switching frequency is 500kHz, ton, and inductor and capacitor values. Design for continuous inductor current. Assume ideal conditions, and assume the output current is symmetric
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
To design a high efficiency d.c., to d.c power converter with the given specifications min 10V max 15V nominal (regulated) 8V Input voltage: Output voltage: Nominal load current: 4A Inductor current ripple: 0.1A max Switching frequency: 30 kHz Output voltage ripple: 20 mV Define a suitable power circuit topology to meet the above specification? Sketch a circuit diagram of the chosen power circuit topology (a) Define the minimum and maximum duty cycles assuming that the control circuit keeps the output...
Design a boost converter power stage to the following specification: Input voltage Output voltage: Output voltage ripple:max 20mV Load power: Switching frequency: 15kHz 110-125V 300V 1.5kW Calculate: (i) Maximum duty cycle (ii) Minimum duty cycle (iii) Average diode current (iv) Assuming the Rds(on) of the MOSFET is 0.01 Ω, and the diode forward voltage is 0.8V, calculate the approximate efficiency of the circuit. 2. A switching power supply shown in the circuit below has its switch driven by a signal...
Most questions answered within 3 hours.
-
given the standard of 200 mg/dl and the absorbance of that
standard is 0.640. What is...
asked 55 seconds ago -
Exercise 8-51 Algo
An accounting professor is notorious for being stingy in giving
out good letter...
asked 8 minutes ago -
month
total distribution cost
level of activity (unit produced)
july
230.000
3500
august
250.000
3750
september...
asked 10 minutes ago -
A smoke detector system uses two devices, A and B. If smoke is
present, the probability...
asked 58 minutes ago -
Your division head has assigned another important project to you
and your team. This project is...
asked 22 minutes ago -
Under normal use conditions, the Mean Time To Failure of a
heating coil can be modeled...
asked 1 hour ago -
Consider the probability that fewer than 34 out of 116 CDs will
be defective. Assume the...
asked 37 minutes ago -
4J Manufacturing Company uses a job order cost accounting system
and keeps perpetual inventory records. Prepare...
asked 27 minutes ago -
Please write code in C++
using recursive function
Write a program that computes the sequence of...
asked 25 minutes ago -
What is 345 as an unsigned decimal number? It is 34
with subscript of 5. Not...
asked 41 minutes ago -
I've been struggling with these homework questions. Any help
would be greatly appreciated
1. For the...
asked 39 minutes ago -
Read the In-Depth Integrative Case 1.2 (Pharmaceutical
Companies, Intellectual Property, and the Global AIDS Epidemic) in...
asked 39 minutes ago