Calculate the maximum bending and shear stress for the cantilever beam with the cross section shown...

Question

Question

Calculate the maximum bending and shear stress for the cantilever beam with the cross section shown

Answer 1

Answer #1

Shear force is constant along the beam.

Bending moment is maximum at fixed end.

iveni 8-30 Kip l= 4 ft. = 48 inch P A R [R =p v] SED BMD Mmax 0 Shear stress is constant along the length of the beam V = Rea

Please rate the answer, thanks in advance.

Answer 2

Similar Homework Help Questions

For the beam cross-section shown below and for an internal shear force Va150 kips and internal...

For the beam cross-section shown below and for an internal shear force Va150 kips and internal bending moment M 1,400 kip-in: opiem 3 3.1) Calculate the moment of inertia of the beam about the x-axis. 3.2) Calculate the maximum bending st 10 Points ress in the section. Indicate on the section where the maximum stress occurs. Points 3.3) Calculate the average shear stress over the cross-section
4. A cantilever beam is loaded as shown in the figure. Using the method of sections...

4. A cantilever beam is loaded as shown in the figure. Using the method of sections or the integration method, draw the shear force diagram and the bending moment diagram. If the beam cross-section is a 9 inch square, find the maximum bending stress 1200 lb 800 lb/ft 9" B 9" A Beam cross-section 8 ft 8 ft
Q3 (25 pts) 3. For the cantilever beam shown below and to the left, Determine the...

Q3 (25 pts) 3. For the cantilever beam shown below and to the left, Determine the reactions at the wall at C. Draw the shear (V) and moment (M) diagram for the beam and label the appropriate values. For the given cross section, determine the magnitude of the maximum COMPRESSIVE bending stress and state where this occurs along the length of the beam and along the height of the beam (top or bottom). Sketch the NORMAL stress distribution (profile) for...

2. Draw Shear Force and Bending Moment Diagram (use your preferred method). Determine Maximum Ten...

2. Draw Shear Force and Bending Moment Diagram (use your preferred method). Determine Maximum Tensile and Compressive Stresses due to bending, state where on the beam these occur. For the mid-point between A and B, determine shear stress at neutral axis; 2" from the top of the flange; at the junction between web and flange and on the top of the flange for the cross-section. Plot of the bending stress and shear stress distribution diagram across the cross section of...
Compute the maximum tensile and compressive bending stress for the cantilever beam with uniform load w = 65 kN/m and the cross-section shown below.

Compute the maximum tensile and compressive bending stress for the cantilever beam with uniform load w = 65 kN/m and the cross-section shown below.
Problem 1 For the loaded beam with the cross-section shown: A. Find the location of the neutral a...

Problem 1 For the loaded beam with the cross-section shown: A. Find the location of the neutral axis B. Compute the moment of inertia of the section around the neutral axis C. Locate the section of maximum moment then compute the maximum stress due to bending, fb D. Locate the section of maximum shear-compute the shear stress at the neutral axis 3.0 k 8" 1.5 k/ft 1.0 k/ft 2" 8 10 ft 6 ft 4 ft 2" Cross-Section Problem 1...

A cantilever beam with a 1-in-diameter round cross section is loaded at the tip with a...

A cantilever beam with a 1-in-diameter round cross section is loaded at the tip with a transverse force of 1000 lbf, as shown in the figure. The cross section at the wall is also shown, with labeled points A at the top, B at the center, and C at the midpoint between A and B. Study the Cross section at the Problem 3-45 significance of the transverse shear stress in combination with bending by performing the following steps. (a) Assume...
To complete this homework, follow the guidelines given in the syllabus (a) Determine the maximum bending...

To complete this homework, follow the guidelines given in the syllabus (a) Determine the maximum bending stress and shear stress for the beam shown made of the standard cross section C 10 × 20. (b) Determine the bending and shear stresses at a point 5 ft from the fixed end and 2 inches from the top surface. 10 kip 8 kip 2 kip/ft 40 kip-ft 4 ft 6 ft
If a cantilever beam is subjected to the following loading, and a cross section of the beam is provided.

If a cantilever beam is subjected to the following loading, and a cross section of the beam is provided. a. determine the maximum bending stress in the beam. b Determine the absolute maximum shear stress in the beam.

A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown....

A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume LAB = 4.0 ft, LBC = 12.0 ft, w = 1620 lb/ft, P = 2550 lb, b = 16 in., d = 6 in., t = 0.50 in. Determine (a) the maximum horizontal shear stress. (b) the maximum compression bending stress. (c) the maximum tension bending stress. Chapter 9, Supplemental Question 043 (GO Tutorial) A cantilever beam supports the loads shown. The cross...