Homework Answers
Add Answer to:
The following dimensions are given for a standard press and shrink fit of a solid shaft...
(b) Perform the following tolerance calculations using the Limits and Fits Calculator and enter d...
here is the shaft dimensions
(b) Perform the following tolerance calculations using the Limits and Fits Calculator and enter data in a textbox on drawing. If a hole basis LN3(H7/r6) interference fit is used for placing the bearing in the hole, what would be the limits of the diameter for the hole and outer diameter of the bearing? Counterbore hole minimum diameter Counterbore hole maximum diameter Bearing outside diameter minimum Bearing outside diameter maximum (c) Perform the following tolerance calculations...
18) Nitrogen (MW-48) is isothermally compressed from 200°F and 40 psia to 100 psia. Calculate the...
18) Nitrogen (MW-48) is isothermally compressed from 200°F and 40 psia to 100 psia. Calculate the final specific volume, the change in entropy and the heat transferred in the process. 8) A steel collar is press fitted onto a steel shaft. The modulus of elasticity of steel-36 x 106 Ib/in2. The collar has an internal diameter- 2.498 in, and the shaft has an outside diameter -2.500 in. The outside diameter of the collar = 4.000 in. (a) Determine the radial...
A press fit is used with an inner aluminum solid disc of radius 1.25" and an outer steel hollow a...
A press fit is used with an inner aluminum solid disc of radius 1.25" and an outer steel hollow annulus of inner radius 1.25" and outer radius 2". If the steel has a yield stress in tension of 36 ksi and the aluminum is 18 ksi, determine the maximum radial interference before yielding will occur. Assume plane stress conditions. Use the MSS theory.
A press fit is used with an inner aluminum solid disc of radius 1.25" and an outer...
P3
Problem 3.A solid round bar is to be assembled into a collar by press fitting. The inside radius of the collar is R = 50 mm and the outside radius is o = 4C mm. Find the maximum allowable radial interference & if the assembly is to have a safety factor of 2 against yielding. Both parts are made of carbon steel having E 200 GPa and Sy = 300MPa Solve using the DET.
V): It is usual practice to design a hub such that its outside diameter is about...
V): It is usual practice to design a hub such that its outside diameter is about twice the bore diameter. It is also known that a selective assembly should be used when shrinking a hub on a shaft. The purpose of this problem is to determine how small and how large stresses can be with a shrink fit (class 8 fit) if a selective assembly is not used. As shown in Fig. 3, determine for a 2" diameter solid shaft,...
please show step by step solution for problem J (J) For the sleeve and bushing of problem (I) if the pressure at the mating surface is 10,260 psi what is the tensile stress in the sleeve? Tens...
please show step by step solution for problem J
(J) For the sleeve and bushing of problem (I) if the pressure at the mating surface is 10,260 psi what is the tensile stress in the sleeve? Tensile stress = 46,470 psi Answer Box: Enter numerical values in italics t Data Inside radius of inner member Outside radius of inner memeber 0.0000 in b 0.5000 in 0.6250 in δ= 0.0019 in E0 = 3.00E+07 psi E- 300E+07 psi Outside radius of...
please write some steps Fig.Q3 A driving shaft is made of steel whose modulus of rigidity...
please write some steps
Fig.Q3 A driving shaft is made of steel whose modulus of rigidity is 80 GN/m2. As shown in Fig.Q3(a), the shaft has a solid circular section and is subjected to a torque of 1400Nm applied, as indicated. 3. Calculate the angle of twist of one end relative to the other and the maximum shear stress which results. (a) As shown in Fig.Q3.(b), part of the shaft is then made hollow by boring a 35 mm diameter...
Help Please A solid steel shaft AC is fixed to a rigid wall at its end...
Help Please
A solid steel shaft AC is fixed to a rigid wall at its end A and is connected to a solid aluminum shaft CD at its other end C. The torques Ti and Tz are applied at the sections R and D, respectively, as shown in the figure. All the dimensions are given in the figure and the weight of the shafts are neglected. The shear modulus of steel is Gst 78 GPa and the shear modulus of...
3.A solid steel shaft (see Figure Q3) free at the ends has a diameter of 25...
3.A solid steel shaft (see Figure Q3) free at the ends has a diameter of 25 mm. LBc 500mm and Lco 250mm. The torques experienced by the shaft are T1 300Nm T2 = 550Nm and T3 = 250Nm. The modulus of rigidity of the material is G- 100GPa BC CD Figure Q3 a) Find the values of the internal torques TBc and Tco taking the anticlockwise direction as positive b) What is the maximum shear stress experienced by the shaft?...
Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm...
Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm. Assume that the bearings shown allow free rotation of the shafts. If a 400 N-m torque is applied at gear D, determine (a) the maximum shear stress magnitudes in each shaft. (b) the angles of twist ф, and ф (c) the...
here is the shaft dimensions
(b) Perform the following tolerance calculations using the Limits and Fits Calculator and enter data in a textbox on drawing. If a hole basis LN3(H7/r6) interference fit is used for placing the bearing in the hole, what would be the limits of the diameter for the hole and outer diameter of the bearing? Counterbore hole minimum diameter Counterbore hole maximum diameter Bearing outside diameter minimum Bearing outside diameter maximum (c) Perform the following tolerance calculations...
18) Nitrogen (MW-48) is isothermally compressed from 200°F and 40 psia to 100 psia. Calculate the final specific volume, the change in entropy and the heat transferred in the process. 8) A steel collar is press fitted onto a steel shaft. The modulus of elasticity of steel-36 x 106 Ib/in2. The collar has an internal diameter- 2.498 in, and the shaft has an outside diameter -2.500 in. The outside diameter of the collar = 4.000 in. (a) Determine the radial...
A press fit is used with an inner aluminum solid disc of radius 1.25" and an outer steel hollow annulus of inner radius 1.25" and outer radius 2". If the steel has a yield stress in tension of 36 ksi and the aluminum is 18 ksi, determine the maximum radial interference before yielding will occur. Assume plane stress conditions. Use the MSS theory.
A press fit is used with an inner aluminum solid disc of radius 1.25" and an outer...
V): It is usual practice to design a hub such that its outside diameter is about twice the bore diameter. It is also known that a selective assembly should be used when shrinking a hub on a shaft. The purpose of this problem is to determine how small and how large stresses can be with a shrink fit (class 8 fit) if a selective assembly is not used. As shown in Fig. 3, determine for a 2" diameter solid shaft,...
please show step by step solution for problem J
(J) For the sleeve and bushing of problem (I) if the pressure at the mating surface is 10,260 psi what is the tensile stress in the sleeve? Tensile stress = 46,470 psi Answer Box: Enter numerical values in italics t Data Inside radius of inner member Outside radius of inner memeber 0.0000 in b 0.5000 in 0.6250 in δ= 0.0019 in E0 = 3.00E+07 psi E- 300E+07 psi Outside radius of...
please write some steps
Fig.Q3 A driving shaft is made of steel whose modulus of rigidity is 80 GN/m2. As shown in Fig.Q3(a), the shaft has a solid circular section and is subjected to a torque of 1400Nm applied, as indicated. 3. Calculate the angle of twist of one end relative to the other and the maximum shear stress which results. (a) As shown in Fig.Q3.(b), part of the shaft is then made hollow by boring a 35 mm diameter...
Help Please
A solid steel shaft AC is fixed to a rigid wall at its end A and is connected to a solid aluminum shaft CD at its other end C. The torques Ti and Tz are applied at the sections R and D, respectively, as shown in the figure. All the dimensions are given in the figure and the weight of the shafts are neglected. The shear modulus of steel is Gst 78 GPa and the shear modulus of...
3.A solid steel shaft (see Figure Q3) free at the ends has a diameter of 25 mm. LBc 500mm and Lco 250mm. The torques experienced by the shaft are T1 300Nm T2 = 550Nm and T3 = 250Nm. The modulus of rigidity of the material is G- 100GPa BC CD Figure Q3 a) Find the values of the internal torques TBc and Tco taking the anticlockwise direction as positive b) What is the maximum shear stress experienced by the shaft?...
Problem 1 (25 Points) Two solid steel (6-80 GPa) shafts are connected by the gears shown. Shaft (1) has a diameter of 45 mm, and shaft (2) has an outside diameter of 55 mm and wall thickness 4 mm. Assume that the bearings shown allow free rotation of the shafts. If a 400 N-m torque is applied at gear D, determine (a) the maximum shear stress magnitudes in each shaft. (b) the angles of twist ф, and ф (c) the...
Most questions answered within 3 hours.
-
The random variable X is exponentially distributed, where X
represents the time it takes for a...
asked 24 seconds from now -
MATLAB
write a MATLAB function (1) output a third-order polynomial
function with the coefficients as the...
asked 7 minutes ago -
A z-score
communicates a raw score’s "relative standing"
under the normal curve in relation to:
asked 15 minutes ago -
An object is vibrating on a spring with the following equation
of motion:
?=(30 ??)cos((2?)/(160)?)
a)...
asked 14 minutes ago -
Vulcan Flyovers offers scenic overflights of Mount St. Helens,
the volcano in Washington State that explosively...
asked 17 minutes ago -
If organizations do not adapt fast enough and move incrementally
from the twentieth-century model to the...
asked 18 minutes ago -
A helium balloon with 2.5L of gas has a gauge pressure of 10,000
Pa. The balloon...
asked 22 minutes ago -
What is responsible for Jupiter's enormous magnetic field?
asked 37 minutes ago -
At the end of the year, a company offered to buy 5,000 units of
a product...
asked 39 minutes ago -
Implement C++ program for each of the following.
Let D = [-48, -14, -8, 0, 1,...
asked 59 minutes ago -
Consider a labor market in which LD = 400 – 4W and LS = 250 +...
asked 1 hour ago -
Let’s say you are teaching a typically-developing young child
how to eat with a spoon. Describe...
asked 56 minutes ago