A voltmeter and an ammeter are used to respectively monitor the voltage across and the current...
A voltmeter and an ammeter are used to respectively monitor the voltage across and the current through a resistor connected to an AC source. If the resistor has a value of 14.0 Ω and the ammeter reads 8.04 A, determine the following. (a) the rms voltage (in V) across the resistor V (b) the peak voltage (in V) of the source V (c) the maximum current (in A) in the resistor A (d) the average power (in W) delivered to...
NTNU ASK YOUR TEACHER voltmeter and an eter are used to respectively monitor the voltage and the current characted to Ver the follow b) the protein V) of the source c) the maximum current in A) in the resistor А d) the average power in W) delivered to the resistor w
When an AC source is connected across a 22.0 Ω resistor, the output voltage is given by Δv = (140 V)sin(70πt). Determine the following quantities. (a) maximum voltage ____ V (b) rms voltage ____ V (c) rms current ____ A (d) peak current ____ A (e) Find the current when t = 0.0045 s. ____ A
When a battery voltage is measured by placing a high-resistance voltmeter across the terminals of the battery, the voltmeter reads 6.3V. With the voltmeter leads still attached, the battery terminals are then connected to a resistor in series with an ammeter. In this arrangement, the ammeter reads 150 mA, and the voltmeter reads 5.9V. What are the emf and the internal resistance of the battery?
When an AC source is connected across a 23.0 12 resistor, the output voltage is given by AV = (160 V)sin(70st). Determine the following quantities. (a) peak voltage (b) rms voltage v (c) rms current (d) peak current (e) Find the current when t = 0.0045 s.
5. A resistor and capacitor are connected in series with an applied AC voltage source. There is no inductor. Separate voltmeter readings across the resistor and capacitor give values of 50 V and 75 V (rms) respectively. What is the (rms) voltage of the source? (5 points)
An AC generator supplies an rms voltage of 120 V at 60.0 Hz. It is connected in series with a 0.450 H inductor, a 5.4 uF capacitor and a 351 ohm resistor. What is the impedance of the circuit? What is the rms current through the resistor? What is the average power dissipated in the circuit? What is the peak current through the resistor? What is the peak voltage across the inductor? What is the peak voltage across the capacitor?...
Generator An AC generator supplies an rms voltage of 220 V at 50.0 Hz. It is connected in series with a 0.700 H inductor, a 5.20 μF capacitor and a 401 Ω resistor. What is the impedance of the circuit? What is the rms current through the resistor? What is the average power dissipated in the circuit? What is the peak current through the resistor? What is the peak voltage across the inductor? What is the peak voltage across the...
You have a 10 ohm resistor connected in series with an ammeter. The voltage applied to the whole circuit is 1.2 volts. At the same time you have a voltmeter connected across the 10 ohm resistor and voltmeter reads 0.9 volts. The circuit draws a total of 0.5 amps. Can you determine resistance of the ammeter?
An ac power supply produces a maximum voltage delta V_max = 100 V. This power supply is connected to a 24.0-ohm resistor, and the current and resistor voltage are measured with an ideal ac ammeter and voltmeter as shown in the sketch below: What does each meter read? An ideal ammeter has zero resistance and an ideal voltmeter has infinite resistance. (70.7 V;2.95 A)
> avg power is not 1/2 * I^2 * R it is I^2 * R
idfwu Mon, Dec 13, 2021 5:12 PM