Question 2 Water is draining from a pressurized tank as shown in the figure. The exit...
A cylinder-type tank filled with water is installed as
follows. When draining the bottom of the tank with a pipe with a
diameter of 5cm, the rate at which the water falls is v= route(2gh)
where g is the gravity acceleration and h is the depth of the water
in the tank at the outlet below the tank. The tank is 12 meters
long and 0.6 meters in diameter. Assuming the tank is half full,
how long does it take...
A 10 cm jet of water issues from a 1 m diameter tank Assume that the velocity in the jet is /2gh m/s where h is the elevation of the water surface above the outlet jet. How long will it take for the water surface in the tank to drop from ho 2 m to h 0.50 m? Problem Definition Situation: Water draining by a 10 cm jet from 1 m diameter tank. Find: Time (in seconds) to drain from...
You are assigned the design of a cylindrical, pressurized water tank for a future colony on Mars, where the acceleration due to gravity is 3.71 meters per second per second. The pressure at the surface of the water will be 105 kPa , and the depth of the water will be 14.1 m . The pressure of the air in the building outside the tank will be 88.0 kPa . Find the net downward force on the tank's flat bottom,...
You are assigned the design of a cylindrical, pressurized water tank for a future colony on Mars, where the acceleration due to gravity is 3.71 m/s2. The pressure at the surface of the water will be 150 kPa , and the depth of the water will be 14.1 m . The pressure of the air outside the tank, which is elevated above the ground, will be 91.0 kPa . Find the net downward force on the tank's flat bottom, of...
You are assigned the design of a cylindrical, pressurized water tank for a future colony on Mars, where the acceleration due to gravity is 3.71 m/s2. The pressure at the surface of the water will be 145 kPa , and the depth of the water will be 14.4 m . The pressure of the air outside the tank, which is elevated above the ground, will be 95.0 kPa . A) Find the net downward force on the tank's flat bottom,...
You are assigned the design of a cylindrical, pressurized water tank for a future colony on Mars, where the acceleration due to gravity is 3.71 meters per second per second. The pressure at the surface of the water will be 125 kPa , and the depth of the water will be 14.0 m . The pressure of the air in the building outside the tank will be 92.0 kPa .
Water flows steadily from an open tank as shown in the figure.
The elevation of
point 1 is H = 13 m ,
and the elevation of points 2 and 3 is h = 2 m .
The cross-sectional area at point 2 is 0.00069 m 2
; at point 3, where the water is
discharged, it is 0.00158 m 2 . The
cross-sectional area of the tank is very large compared with the
cross-sectional area of the pipe. Find...
The figure shows a cylindrical tank of 80 em in diameter which is fully filled with water. In order to increase the flow from the tank to the exit pipe on the left, an additional pressure is applied to the water surface by an air compressor to supply air to the upper air chamber of the tank. The external walls of the tank are exposed to the atmospheric conditions of the area. You are required to determine the hydrostatic conditions...
Can I know full answer
2. Pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to the atmosphere. The water level is 3 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) while the atmospheric pressure is 100 kPa. Neglecting frictional effects, determine the initial discharge rate of water from the tank. Air 00 kPa 3 m 10 cm