Question

A ductile solid circular loar of 0,2 m in diameter is loaded as shown in the figure. The tensile stress-strain response of th

0 0
Add a comment Improve this question Transcribed image text
Answer #1

swess according Sut = according to von-mises anterian, 2+372 But = 32.30 mp we san see from the graph syt say the material is

Add a comment
Know the answer?
Add Answer to:
A ductile solid circular loar of 0,2 m in diameter is loaded as shown in the...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • 1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test...

    1 Figure 2. The specimen was loaded to 7 You have been provided the tensile test results shown in Figure 2. The specimen fracture. Using these results, determine the following: Young's Modulus (3 points). The Yield Stress at 0.2% offset (3 points). The Ultimate Tensile Stress (1 point). The percent elongation at failure (1 point). • The toughness of the material (2 points). --- - -- Stress (o) (MPa) 0.04 0.035 0 0.045 0 0.005 0.01 0.015 0.02 0.025 0.03...

  • A ships solid circular drive shaft... A ships solid circular drive shaft is of diameter, d...

    A ships solid circular drive shaft... A ships solid circular drive shaft is of diameter, d 53 mm, and is subjected to a torque, T= 1512 Nm and an axial force, F-134 kN as shown. The shaft is made of steel with a yield stress of 350 MPa. Determine the Factor of Safety (accurate to two decimal places), according to Tresca's maximum shear stress failure theory. (Hint: Based on the state of stress in a surface element, consider Mohr's circle...

  • 3-5 A circular aluminum plate 1 m in diameter and 5 cm in thickness is loaded by a uniform pressu...

    Need ANSYS Code elastic modulus E = 68.9 Gpa possion ratio v = .33 3-5 A circular aluminum plate 1 m in diameter and 5 cm in thickness is loaded by a uniform pressure of 0.5 Pa distributed over a 0.25 m diameter circle at the center of the plate. The outer edges of the plate are completely fixed from motion. Find the maximum deflection and von Mises stress and their locations. 3-5 A circular aluminum plate 1 m in...

  • Q4. A bar shown below is loaded at its end acting perpendicular to the diagram, Strain...

    Q4. A bar shown below is loaded at its end acting perpendicular to the diagram, Strain Gauge Length A = 700mm Length B = 350.0mm Length C = 480.0mm Diameter D = 10.0mm Poisson's Ratio = 0.3 E= 220GP a) If the yield stress of the material (steel) is 200 MPa, calculate the maximum load (in Kg) that can be applied to the bar using Von Mises Criterion using a factor of safety of 1.5 (Marks - 5) b) Hence...

  • Answer is 2.84 Question 1 A ships solid circular drive shaft is of diameter, d-54 mm,...

    Answer is 2.84 Question 1 A ships solid circular drive shaft is of diameter, d-54 mm, and is subjected to a torque, T steel with a yield stress of 350 MPa. 1700 Nm and an axial force, F-127 kN as shown. The shaft is made of Determine the Factor of Safety (accurate to two decimal places), according to Tresca's maximum shear stress failure theory. (Hint: Based on the state of stress in a surface element, consider Mohr's circle to get...

  • (a) Determine the strain energy of a solid brass circular shaft ABC loaded as shown in...

    (a) Determine the strain energy of a solid brass circular shaft ABC loaded as shown in Fig. P2.61, assuming that the stress concentrations may be omitted. (b) Calculate the strain energy for T 1.4 kN.m, a - 500 mm, d 20 mm, and G 42 GPa. 1.4d TB 4T 1.2a FIGURE P2.61

  • An existing steel beam is in use in a building.

    An existing steel beam is in use in a building. Using a rectangular strain gauge rosette, the actual strains at point A have been recorded while being subjected to test loads which simulate crowd loading. It is necessary to calculate the principal stresses to check whether the beam is safe for its current purpose (ie: assess whether the stresses determined are less than the maximum permissible stresses) Figure 4: Strain gauge rosette location and recorded strains In this case it is reasonable...

  • Problem 2: A circular shaft transmits power as shown with pulley loads. The shaft carries a...

    Problem 2: A circular shaft transmits power as shown with pulley loads. The shaft carries a torque, bending, shear and axial loads. Draw LVM diagram to find Mmax and Vmax. Show all loads (moments and forces) on the circular x-section of the shaft below. Use double arrows for moments. Compute shear and normal stresses and show them on the same section. Create stress elements for points A and B of the section. Combine the stresses and compute Cuau (Tresca) and...

  • A circular shaft transmits power as shown with pulley loads. The shaft carries a torque, bending,...

    A circular shaft transmits power as shown with pulley loads. The shaft carries a torque, bending, shear and axial loads. Draw LVM diagram to find Mmax and Vmax. Show all loads (moments and forces) on the circular x-section of the shaft below. Use double arrows for moments. Compute shear and normal stresses and show them on the same section. Create stress elements for points A and B of the section. Combine the stresses and compute tmax (Tresca) and om (von...

  • Problem 2: A circular shaft transmits power as shown with pulley loads. The shaft carries a...

    Problem 2: A circular shaft transmits power as shown with pulley loads. The shaft carries a torque, bending, shear and axial loads. Draw LVM diagram to find Mmax and Vmax. Show all loads (moments and forces) on the circular x-section of the shaft below. Use double arrows for moments. Compute shear and normal stresses and show them on the same section. Create stress elements for points A and B of the section. Combine the stresses and compute Tmax (Tresca) and...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT