SOLUTION:
A solid shaft of Diameter D, is subjected with Distributed and concentrated torsion as shown in the Figure.
Given:
Diameter(D) = 50mm
(cw) ;
G = 75 GPa
BY SUPERPOSITION METHOD:
Let, Twisting Angle , due to T(A) , T(C) and t, is
so,
SIMILARLY,
Now for, twist angle due to uniform distributed torsion,
So, twist angle at free end,
The 50-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and...
The 50-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and concentrated torsional loadings shown where T = 140 N-m. 2 kNm 600 Nm B 0.8 m 0.6 m A Part A Determine the angle of twist at the free end A of the shaft due to these loadings. Use Gst = 75.0 GPa Express your answer to three significant figures and include appropriate units. μΑ ? 22 % Å O 0.303 Submit Previous Answers...
The 50-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and concentrated torsional loadings shown where T = 140 N-m. 2 kNm 600 Nm B 0.8 m 0.6 m A Part A Determine the angle of twist at the free end A of the shaft due to these loadings. Use Gst = 75.0 GPa Express your answer to three significant figures and include appropriate units. μΑ ? 22 % Å O 0.303 Submit Previous Answers...
The 50-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and concentrated torsional loadings shown where T = 230 N-m. 2 kNm 600 Nm B 0.8 m 0.6 m Part A Determine the angle of twist at the free end A of the shaft due to these loadings. Use Gst = 75.0 GPa Express your answer to three significant figures and include appropriate units. μΑ ? O= Value Units
A solid shaft with 100-mm-diameter is made of cast iron and is subjected to the distributed and concentrated loadings as shown in Figure 9. The shear modulus of cast iron is 39GPa. (A) Determine the angle of twist at the free end A of the shaft due to these loadings. [9 marks] (B) Determine the maximum shear stress in this shaft. [4 marks] (C) Cast iron is a brittle material with an ultimate strength of 260MPa. Determine whether this structure...
The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the absolute maximum and minimum shear stresses in the shaft's surface and specify their locations, measured from the free end. 10-25. The solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine the required diameter d of the shaft if the allowable shear stress for the material is Tallow = 60 MPa. 400 N·m 4 kN.m/m А. < 0.2 m 0.2 m...
The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T 330 Nm. 2 kN·m/m 0.4 m 600 N m 0.4 m 0.3 m 0.3 m Q Tap image to zoom The allowable shear stress for the material is Tallow-160 MPa. Part A Determine the required diameter d of the shaft Express your answer to three significant figures and include appropriate units. alue Units Submit Request Answer
Part A The 56-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T-470 N-m(Figure 1) Determine the absolute minimum shear stress on the shall's surface, and specify its location, measured from the fixed end C Express your answers, separated by a comma, to three significant figures. VAE 11 vec o ? T min MPa.mn Submit Request Answer Figure 1 of 1 Part B 2 kN.m/m Determine the absolute maximum shear stress on the shaft's surface,...
5. A 38-mm-diameter solid steel shaft, 2 m long, is subjected to a torque of 600 N.m, as shown below. The steel is AISI 1020 hot-rolled. Calculate a) The maximum torsional shear stress b) The angle of twist, ?, in degrees, ifG2 79.3 x 10"MPas 79.3 x 10, N/m2 Te TL Recall radian 57.3 32 JG
The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T = 410 N·m. 2 kN.m/m 0.4 m / B 600 N·m A 0.4 m d The allowable shear stress for the material is Tallow = 175 MPa. Part A Determine the required diameter d of the shaft.
A. What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6-m length when subjected to a torque of 12 kN·m? Use G = 83 GPa. B. Determine the bearing stress of the punch out plate of the precious problem, Answer in MPa