Homework Answers
Please Rate,
Thank You!!!
Add Answer to:
> A concrete wall has a constant temperature Ty on its left side. It experiences forced...
P1 (50 pts.) - A large plane wall has a thickness L-60 cm and thermal conductivity...
P1 (50 pts.) - A large plane wall has a thickness L-60 cm and thermal conductivity k 25 W/m-K. On the left surface (x-0), it is subjected to a uniform heat flux qo while the surface temperature To is constant. On the right surface, it experiences convection and radiation heat transfer while the surface temperature is TL-225°C and the surrounding temperature is 25°C. The emissivity and the convection heat transfer coefficient on the right surface are 0.7 and 15 W/m2-K,...
A wall (assumed to be 1-dimensional) has a thickness of 2L-8em and experiences uniform thermal energy...
A wall (assumed to be 1-dimensional) has a thickness of 2L-8em and experiences uniform thermal energy generation of 9 1000 ms. The wall is cooled convectively at x = ±4 cm by a fluid at temperature T,-30°C. The steady-state temperature distribution through the wall is T(x) = a(L2-x*) + b, where a = 15°C/mz and b = 40°C. Determine 4. a. b, The thermal conductivity of the wall, k The convection coefficient, h
A plane wall of thickness 2L= 30 mm and thermal conductivity k= 3 W/m·K experiences uniform...
A plane wall of thickness 2L= 30 mm and thermal conductivity k= 3 W/m·K experiences uniform volumetric heat generation at a rate q˙, while convection heat transfer occurs at both of its surfaces (x=-L, +L), each of which is exposed to a fluid of temperature ∞T∞= 20°C. Under steady-state conditions, the temperature distribution in the wall is of the form T(x)=a+bx+cx2 where a= 82.0°C, b= -210°C/m, c= -2 × 104°C/m2, and x is in meters. The origin of the x-coordinate...
The steady state temperature distribution across a wall, where -0.02 m, is T(X)*+bx+ A uniform heat...
The steady state temperature distribution across a wall, where -0.02 m, is T(X)*+bx+ A uniform heat generation rate. 9. ration rate. 9. Occurs in the wall and is given in the table below. Coefficients a, b and care in units shown in the table and x is in meters. The origin of the x coordinate is at the middle of the wall as shown. Each side of the wall experiences convection from a fluid at -20°C 82 K (thermal conductivity...
A concrete basement wall has thickness of 0.2 m. How much heat flows per square meter...
A concrete basement wall has thickness of 0.2 m. How much heat flows per square meter per second if the basement temperature is 25 ◦C and the ground temperate is 7 ◦C. Take the coefficient of conductivity of concrete to be 0.8 W m·K (a) 72 J (b) 58 J (c) 25 kJ (d) 5.8 J (e) 1.8 J
Heat is uniformly generated at the rate of 2x 10W/m* in a wall of thermal conductivity...
Heat is uniformly generated at the rate of 2x 10W/m* in a wall of thermal conductivity 25 W/m-K and thickness 60 mm. The wall is exposed to convection on both sides, with different heat transfer coefficients and temperatures as shown. There are straight rectangular fins on the right-hand side of the wall, with dimensions as shown (L =20 mm) and thermal conductivity of 250 W/m-K. What is the maximum temperature that will occur in the wall? L tt-2 mm k=25...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m * 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer coefficient...
Consider a large plane wall of thickness L= 0.5 m, thermal conductivity k = 2.5 W/m...
Consider a large plane wall of thickness L= 0.5 m, thermal conductivity k = 2.5 W/m °C, and surface area A = 50 m². The left side of the wall is maintained at constant temperature To = 100 °C, while the right side is maintained at T4 = 10 °C. Taking the nodal spacing to be 4x = 12.5 cm: 1. obtain the finite difference formulation for all internal nodes (1,2,3), 2. determine the internal nodal (1,2,3) temperatures by solving...
3. The wall shown in the figure below has thickness L 0.25 m and uniform thermal...
3. The wall shown in the figure below has thickness L 0.25 m and uniform thermal conductivity k-1 W/mK. It is exposed to circulating fluid on the surface at x = L, where the temperature ofthe fluid is T-= 30°C and the convection coefficient is h = 4 W/m2.K. The surface at x = 0 is maintained at constant temperature T-20 °C. Assume ID heat flux, and that the system is at steady state a) b) Determine the temperature distribution...
P1 (50 pts.) - A large plane wall has a thickness L-60 cm and thermal conductivity k 25 W/m-K. On the left surface (x-0), it is subjected to a uniform heat flux qo while the surface temperature To is constant. On the right surface, it experiences convection and radiation heat transfer while the surface temperature is TL-225°C and the surrounding temperature is 25°C. The emissivity and the convection heat transfer coefficient on the right surface are 0.7 and 15 W/m2-K,...
A wall (assumed to be 1-dimensional) has a thickness of 2L-8em and experiences uniform thermal energy generation of 9 1000 ms. The wall is cooled convectively at x = ±4 cm by a fluid at temperature T,-30°C. The steady-state temperature distribution through the wall is T(x) = a(L2-x*) + b, where a = 15°C/mz and b = 40°C. Determine 4. a. b, The thermal conductivity of the wall, k The convection coefficient, h
The steady state temperature distribution across a wall, where -0.02 m, is T(X)*+bx+ A uniform heat generation rate. 9. ration rate. 9. Occurs in the wall and is given in the table below. Coefficients a, b and care in units shown in the table and x is in meters. The origin of the x coordinate is at the middle of the wall as shown. Each side of the wall experiences convection from a fluid at -20°C 82 K (thermal conductivity...
Heat is uniformly generated at the rate of 2x 10W/m* in a wall of thermal conductivity 25 W/m-K and thickness 60 mm. The wall is exposed to convection on both sides, with different heat transfer coefficients and temperatures as shown. There are straight rectangular fins on the right-hand side of the wall, with dimensions as shown (L =20 mm) and thermal conductivity of 250 W/m-K. What is the maximum temperature that will occur in the wall? L tt-2 mm k=25...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m * 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer coefficient...
Consider a large plane wall of thickness L= 0.5 m, thermal conductivity k = 2.5 W/m °C, and surface area A = 50 m². The left side of the wall is maintained at constant temperature To = 100 °C, while the right side is maintained at T4 = 10 °C. Taking the nodal spacing to be 4x = 12.5 cm: 1. obtain the finite difference formulation for all internal nodes (1,2,3), 2. determine the internal nodal (1,2,3) temperatures by solving...
3. The wall shown in the figure below has thickness L 0.25 m and uniform thermal conductivity k-1 W/mK. It is exposed to circulating fluid on the surface at x = L, where the temperature ofthe fluid is T-= 30°C and the convection coefficient is h = 4 W/m2.K. The surface at x = 0 is maintained at constant temperature T-20 °C. Assume ID heat flux, and that the system is at steady state a) b) Determine the temperature distribution...
Most questions answered within 3 hours.
-
An empty test tube weighs 15.923 grams. Then,
MgCl2•6H2O is added into the test tube. After...
asked 38 minutes ago -
Please answer true or false. Words
cannot be changed or added in to make it true...
asked 37 minutes ago -
(a) A piston at 6.1 atm contains a gas that occupies a volume of
3.5 L....
asked 37 minutes ago -
Assume memory access is 10 units of time and disk access is
10000 units of time....
asked 56 minutes ago -
1. Are all good samples random?
2. Magazines often report surveys giving statistics such as “63%...
asked 1 hour ago -
Under all the various types of market structures, firms
must eventually earn some economic profits for...
asked 1 hour ago -
Consider the following fitness regime for a single locus trait
with two co-dominant alleles: w11 =...
asked 1 hour ago -
A large cable company reports the following.
80% of its customers subscribe to its cable TV...
asked 1 hour ago -
Please answer the question in brief.
Discuss the role of ERP in organizations. Are ERP tools...
asked 1 hour ago -
Discuss the pros and cons of collaborative software such
as SameTime. Does it increase productivity? What...
asked 1 hour ago -
Buying your in-laws a gift because it’s expected is
due to the ____________ motive of gift-giving....
asked 1 hour ago -
Calculate the expected value, the variance, and the standard
deviation of the given random variable X....
asked 2 hours ago