correct option ==>> A. 32 inches
please give thumbs up
4. A straight pull box is to be used in a 4-inch conduit run that will...
A rooe is tied to a box and used to pull the box A rope is tied to a box and used to pull the box 1.9 m along a horizontal floor. The rope makes an angle of 30° with the horizontal and has a tension of 5 N. The opposing friction force between the box and the floor is 1 N Part A How much work does gravity do on the box? Express your answer in Joules to one...
What size Intermediate Metal Conduit is required for Four (4) #600 kcmil Type THW Conductors? A. 2" B. 2 1/2" C. 3" D. 3 1/2" E. 4" F. 5" G. 6" What is the minimum number of duplex outlets required along a 32 foot living room wall? A. 2 B. 3 C. 4 D. 5 E. 6 F. 7 G. 8 H. 9
i need help with number 3&4 and the answer is in red i just need to know how to work the problem (a) y (b) y=-x3 + 6x2-9x + 3 2. The sum of two nonnegative numbers is 36 (a) Find the two numbers if the differ ence of their square roots is to be as large as possible. 0 and 36 (b) Find the two numbers if the sum of their square roots is to be as large as...
D. trade size 1 1/2 (41). Atrade size 4 (21). B.trade size 1 (27). (53). Ctrade size 1 1/4(35). E. trade size 2 Code reference 29. The general use 125-volt receptacles in a commercial building are supplied by 20- ampere rated multiwire branch-circuits with three ungrounded conductors anda common neutral from a 208/120-volt, 4-wire, 3-phase electrical system. The con ductors for nine circuits are run in a single raceway to an area of the building includ ing nine ungrounded conductors...
A plate girder cross section consists of two flanges, 1 ½ inches × 15 inches, and a 5/16-inch × 66-inch web. A572 Grade 50 steel is used. The span length is 55 feet, the service live load is 2.0 kips/ft, and the dead load is 0.225 kips/ft, including the weight of the girder. Bearing stiffeners are placed at the ends, and intermediate stiffeners are placed at 6-2" and 12'-9" from each end. Does this girder have enough shear strength? a....
The Box Problem Take an 8% x 11 sheet of paper and cut out 4 congruent squares (one from each corner) as shown below on the left. This creates a net for an open-topped box (rectangular prism) which can be folded up as shown on the right. We're going to use our box to carry as many M & M's as possible. If the side-length of each cut-out square is 1 inch, then the box created will have dimensions 1...
P BUUIS - PULL Kane Brown Radio Cricut Design Space E Log in to Carwasp box - leslieprezea... 78 Notifications N Netflix Question 16 of 50 Draw the Lewis structure of NOCI and then determine the number of nonbonding electron pairs on the central atom. A) O B) 1 C) 2. D) 4 D) 4 E)6 E) 6 to draw a new structure w] Se
3. I have a box with 4 blue chips and 6 white chips. I randomly pull a chip from box 1and put it in box 2 which contains 3 blue chips and 8 white chips. Then I randomly pull a chip from box 2 and put it in box 3 which contains 6 blue chips and 3 white chips. a) What is the probability I pull a blue chip from box 3? b) What is the probability I pull a...
pleas help me in this do any question you know using National Electrical Code 2011 Applied Electricity NEC worksheet t hree Copper conductors with THHN insulation run in Electrical A branch-circuit Consther conductors. The conductor terminations are rated for a maximum ure in the area of this installation is not expected to exceed 30C size 8 AWG, the maximum ampacity of the conductors If the conductors for this circuit are permitted A 40 amperes. B. 50 amperes. to be used...
question 1 and 2 please 1. A one-inch diameter steel rod is used as a pin-pin connected compression member. Calculate the critical load using Euler's formula. The proportional limit for the steel is 36,000 psi and the modulus of elasticity is 30,000,000 psi, (the radius of gyration for a circular section is d/4). Assume the length of the rod to be: A. 1.5 feet B. 4.5 feet Comment on the results of A and B. 2. A one-inch diameter steel...