Which routing protocol provides common view of topology for network devices? RIP IS-IS O IGRP O...
Match statements with the correct routing protocol. RIP OSPF EIGRP Has slow convergence time о O Use inverse of the link bandwidths to calculate cost value O oo Select a DR and BDR inside the area Uses DUAL Algorithm Supports subnetmasks with network command O о Sends periodical updates O O In OSPF, an ASBR must connect backbone area (area O) True
. Consider the network shown below. Suppose AS3 and AS2 are running RIP for their intra-AS routing protocol. Suppose AS1 and AS4 are running OSPF for their intra-AS routing protocol. Suppose eBGP and BGP are used for the inter-AS routing protocol. Initially suppose there is no physical link between AS2 and AS4. 2c a. Router 4c learns about prefix x from which routing protocol: OSPF, RIP, eBse or iBR? b. Router 3b learns about x from which routing protocol? c....
Using the following output, which of the routes is the default gateway? A. 192.168.3.0/24 [1/0] via 192.168.1.1 B. 192.168.1.0/24 is directly connected, FastEthernet0/0 C. 192.168.5.0/24 is directly connected, FastEthernet0/1 D. 192.168.10.0/24 [90/284160] via 192.168.1.1, 00:04:19, FastEthernet0/0 E. None of the above Router1#show ip route Codes: C connected, S- static, R RIP, M - mobile, B BGP D EIGRP, EX EIGRP external, O OSPF, IA OSPF inter area N1 - OSPF NSSA external type 1, N2 -OSPF NSSA external type 2...
Question 19 3 pts (TCO 5) Which command will provide information specific to OSPFv3 routes in the routing table? show ip route ospf show ip route ospfv3 show ipv6 route show ip route ospf show ipv6 route ospf Flag this Question Question 20 3 pts (TCO 5) A network administrator enters the command ipv6 router ospf 64 in global configuration mode. What is the result of this command? The router will be assigned an autonomous system number of 64. The...
PLEASE ATTACH A SCREENSHOT OF YOUR SUCCESSFUL PING IN PACKET TRACER FOR THE END!!!!!!!!!!! THANK YOU! Objectives Part A: Configure a simple static routing . Part B: Configure a simple RIP routing Part A: Configure a simple static routing 1. Create the following network topology on Packet Tracer Router-PT Router-PT Addressing Table Device Interface IP Address Subnet Mask Default Gatewa 10.0.0.1 20.0.0.1 30.0.0.1 20.0.0.2 0.0.0.10 30.0.0.10 N/A 255.0.0.0 255.0.0.0 255.0.0.0 255.0.0.0 255.0.0.0 255.0.0.0 Routero 2/0 NIA NIA NIA 10.0.0.1 30.0.0.1...
Assignment: Which of the following statements accurately describe a link-state routing protocol? (Choose 3) A. The link state database is used to calculate the paths with the highest bandwidths on the network. B. Link-state routing protocols respond quickly to network changes. C. In Link-state routing protocols, each router periodically sends messages to the network, listing the routers to which it is directly connected and also information about whether the link to each router is active. D. Link-state routing protocols send...
a.) Which of the following commands lists active network devices when executed with no arguments? ifconfig nmcli ifdown ifup b.) Some Linux distributions include __________, an automated tool that configures network settings without any interaction on your part. ESSID Network Manager WPA ARP c.) Which of the following is not true regarding the ip command? The ip command is no longer under development. The ip command is designed to replace the ifconfig, arp, and route commands. If you inherit an...
computer networking help 4. 120 points) Consider a network with the following topology (1) Use Djikistra shortest path algorithm to find the spanning tree which contains all form router A to the rest of the routers the network. Show the first 4 steps of the results of the algorithm. (Note that unless specified in figure, all link metrics are 1.) Answer: Step N LA 3.A 2.A (2) Assume that RIP is used as the routing protocol and all link metrics...
PLEASE ATTACH A SCREENSHOT OF THE RE-POPULTATED TABLE AT THE END Objectives Part A: Configure Devices and Verify Connectivity . Part B: Gather Information with Show Commands Tasks Create the following network topology on Packet Tracer Addressing Table 10.10.10.0/24 10 SW1 Device InterfaceIP Address Subnet Mask Default Gateway .1 PC1 10.10.10.1 255.255.255.0 NIA f0/o RTA 10.10.20.1 255.255.255.0NIA f0/1 RTA .1 PC1 255.255.255.010.10.10.1 NIC 10.10.10.10 10.10.20.0/24 PC2 NIC 10.10.20.10 255.255.255.0 10.10.20.1 10 SW2 PC2 Part A: Configure Devices and Verify Connectivity...
Refer to the exhibit. The output of 'show interface g0/0' command on Router-1 can be used to troubleshoot EIGRP adjacency problem. 30/0 80/1 Router 1 Router 2 OK? Method Status Rlish ip interface brief Interface IP-Address Protocol GigabitEthernet0/0 10.10.0.2 GigabitEthernet0/1 unassigned down vlani unassigned down YES manual up up YES unset administratively down YES unset administratively down O True O False Why does OSPF uses Designated Router(DR)? (choose two? Reduce the number of adjacencies over a multiaccess network To summaries...