Question

What is the approximate super-elevation rate for a curve with a 2,000ft radius on highway with a design speed of 65mph? The maximum design super-elevation is 6% for this highway. a) b) c) Please determine the approximate super-elevation rate If max design super-elevation is 6%, does it meet the requirement? (yes/no) PLEASE SHOW ALL STEPS AND EXPLAIN. THANKS

0 0
Add a comment Improve this question Transcribed image text
Answer #1

Super elevation Can be given by a formula OR uohere e super elevation fs friction vclo cty o: Oravitational accele raton nthetheor behind super ete vdio 2-2 → when a body travels on cured Fath, due to centrifugal tor, it tan be hon auay trom the curv2.3 It can be obtained by taki ng 5°/. ob den in 의R f tha obtained valuei lem than latandard) au maxim um pemitted Value, OUTうf 它 outer side Contu road LS E: height to which outer edge lifted| nner edge.

Add a comment
Know the answer?
Add Answer to:
What is the approximate super-elevation rate for a curve with a 2,000ft radius on highway with...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • 2. A horizontal curve on a 4 lane highway has a super elevation of 6% and...

    2. A horizontal curve on a 4 lane highway has a super elevation of 6% and a central angle of 40 degrees. The PT of the curve is at station 322+50 and PI is at 320+08. The road has 10 feet lanes, 2 lanes in each direction, no median, and 8 feet shoulders on both sides. What is the highest safe speed (round to 5mi/hr increments) and what is the station for PC?

  • curve of radius 250ft and e-0.08 is located at a section of an existing rural highway, which restrict the safe speed...

    curve of radius 250ft and e-0.08 is located at a section of an existing rural highway, which restrict the safe speed at this section of the highway to 50 percent of the design speed. This drastic reduction of safe speed resulted in high accident rate at this section. To reduce the accident rate, a new alignment is to be designed with a horizontal curve. Determine the minimum radius of this curve if the safe speed should be increased to the...

  • tme Ens EXAMPLE 3 On a highway, horizontal curve radius is 400m, design speed is 70 km/h, platform width is 10m and normal crown is 2%. Superelevation will be applied this curve without transit...

    tme Ens EXAMPLE 3 On a highway, horizontal curve radius is 400m, design speed is 70 km/h, platform width is 10m and normal crown is 2%. Superelevation will be applied this curve without transition curve and widening . Calculate superelevation that will be applied on this curve . Calculate superelevation application length . Draw inside and outside edge elevation change with respect to inside edge line (schematic superelevation profile tme Ens EXAMPLE 3 On a highway, horizontal curve radius is...

  • A curved highway has only one lane with a centerline radius of 800 ft. A building...

    A curved highway has only one lane with a centerline radius of 800 ft. A building is located 25 ft. from the centerline. The road is level. Take the coefficient of braking friction as 0.36 and perception-reaction time as 2.5 seconds. A.Determine the appropriate speed limit on the curve to ensure stopping sight distance B.Determine the rate of super-elevation (assume that the coefficient of side frictionis0.15)

  • A flat (unbanked) curve on a highway has a radius of 250 m

    A flat (unbanked) curve on a highway has a radius of 250 m. A car successfully rounds the curve at a speed of 35 m/s but is on the verge of skidding out. a. Draw free body diagram of the car. b. If the coefficient of static friction between the car's tires and the road surface were reduced by a factor of 2, with what maximum speed could the car round the curve without slipping? c. Suppose the coefficient of friction were increased...

  • Can you please do this questions? A horizontal curve on a two-lane highway (12 ft lanes)...

    Can you please do this questions? A horizontal curve on a two-lane highway (12 ft lanes) has a PC at station 123+80 and PT as station 129+60. The central angle is 30 degree, the super-elevationis 0.06 and 22 ft is cleared (for sight distance) from the inside edge of the innermost lane. Determine a maximum sate speed (assuming current design standards) to the nearest 5 mi/h.

  • highway geometric Q1) A. What are the Principal elements of the highway cross section? Draw the...

    highway geometric Q1) A. What are the Principal elements of the highway cross section? Draw the typical cross sections for a two-lane highway. (5 Points) B. Briefly discuss the various indirect design factors to be considered for geometric design of highway. (10 Points) Q2) A. What is Road Alignment? Briefly describe the requirements of an ideal alignment. (5 Points) B. An equal-tangent sag vertical curve has the initial grade is -3.2% and the final grade is +1.8%, PVI at 30+30...

  • A concrete highway curve of radius 70.0 m is banked at an 11 degree angle. What...

    A concrete highway curve of radius 70.0 m is banked at an 11 degree angle. What is the maximum speed with which a 1200 kg rubber-tired car can take this curve without sliding? (Take the static coefficient of friction of rubber on concrete to be 1.0.)

  • A car is driving around a flat highway curve that has a radius of 100 meters....

    A car is driving around a flat highway curve that has a radius of 100 meters. The coefficient of friction between the wheels and pavement is 0.8. Please show work! A) Draw a force diagram for the car. What is the force responsible for the centripetal acceleration of the car? B) What is the fastest speed the car can drive around the curve?

  • 9:381 LTE Problem 1 A crest vertical curve is to be designed to join a +2% grade with a-2% at a s...

    9:381 LTE Problem 1 A crest vertical curve is to be designed to join a +2% grade with a-2% at a section of a two-lane highway. Determine the minimum length of the curve if the design speed of the highway is 60 mph and SL. Assume that a-9.34 ftsec' and that the perception-reaction time is 2.5 sec. Problem2 A crest vertical curve is to be designed to join a +3% grade with a-2% grade at a section of a two-lane...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT