can someone answer all parts and show how you did it? Thank you!! no extra info...
part c=d How much force must you and your friend each apply to the free end of the door on the same side and perpendicular to the plane of the door in order to produce the same torque as that produced by both of you in part (a) above? N (d) What is the angular acceleration of the door? rad/s2 A heavy swing door has a mass of m = 7,500 kg, a width W = 1.9 m, and a...
Q5 Thanks in advance. I will rate up the correct answer, and down the wrong one. A heavy swing door has a mass of m = 4,000 kg, a width w = 1.0 m, and a height H = 2.7 m. The door swings about a vertical axis passing through its center. The moment of inertia of this door about the vertical axis of rotation is given by I = 1/12 mw^2. (a) You stand on one side and push...
Sakai @ PC: Gateway: Welcome Google Slides Rotational Motion and Oscillations - EPS 101, section o -/4 POINTS OSUNIPHYS1 10.7.WA.057. MY NOTES ASK YOUR TEACHER A heavy swing door has a mass of m - 4,000 kg, a width w = 1.4 m, and a height H - 2.9 m. The door swings about a vertical axis passing through its center. The moment of inertia of this door about the vertical axis of rotation is given by I m w....
Please solve this question, and show steps. Thank you so much. A uniform rod is set up so that it can rotate about an axis at perpendicular to one of its ends. The length and mass of the rod are 0.711 m and 1.13 kg, respectively. A force of constant magnitude Facts on the rod at the end opposite the rotation axis. The direction of the force is perpendicular to both the rod's length and the rotation axis. Calculate...
A door with mass M= 3.00 kg and width L=2.00m is hinged at one side so that it can rotate without friction about a vertical axis. A heavy bullet embeds in the 3L/4 of the door after it is fired as shown. The mass of the bullet is m=0.200kg and the initial speed of the bullet is speed 410 m/s . Part A Part complete What is the angular speed of the bullet and the door after the bullet embeds...
1. Find angular speed of door after collision 2. What is the change in kinetic friction? A 1.5m wide door (mass 15kg) is hinged at one side so that it can rotate without friction about a vertical axis. It is unlatched. A police officer fires a bullet with a mass of 10g and a speed of 400m/s into the exact center of the door, in a direction perpendicular to the plane of the door. Find the angular speed of the...
PLEASE SHOW WORK AND ANSWER ALL PARTS. WHEN I ASKED THE SECTIONS SEPARATELY THE ANSWERS DID NOT MATCH, THANK YOU!!! All of the questions on this concern a space station, consisting of a long thin uniform rod of mass 4.4 x 106kg and length 171 meters, with two identical uniform hollow spheres, each of mass 1.3 x 106 kg and radius 57 meters, attached at the ends of the rod, as shown below. Note that none of the diagrams shown...
Please answer all parts of question (a-c). 4:45 PM 33% AT&T Notes May 1, 2019 at 4:45 PM Problem 1 a) A uniform beam (5.00 m long, 40.0 kg) is attached to the wall and supported by a cable at the far end, as shown. A 60.0 kg box is placed in the middle of the beanm What is the tension in the cable? b) A wheel in the shape of a solid disk (mass 250 g, radius 30.0 cm)...
Suppose that you are holding a pencil balanced on its point. If you release the pencil and it begins to fall, what will be the angular acceleration when it has an angle of 10.0 degrees from the vertical?What is the distance rn between the point of application of n? and the axis of rotation? What is the distance rw between the point of application of w? and the axis? There are two reasonable approximations to consider for the pencil in this problem: a...