6.32. A rigid vessel contains 0.014 m3 of saturated-vapor steam in equilibrium with 0.021 m of...
An insulated rigid vessel contains 5kg of saturated liquid-vapor mixture of Refrigerant- 134a at 200kPa. At this stage, one-fifth of the mass is in vapor phase and rest is in liquid. Now using an electrical resistance heater, heat is supplied to the contents of the vessel until all of the refrigerant is converted to saturated vapor. Show this process on a P v diagram with respect to saturation lines and determine, 1. volume of the rigid vessel 2. temperature, in...
Pressure in tank = 2320 kPaQuality of saturated mixture = 0.0269A 9.8 m3 rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the rest is in the vapor form. Determine the density of the mixture. (Round the final answer to one decimal place.) (You must provide an answer before moving on to the next part.) The saturated water-temperature table (in Sl units) is given below.The density of the mixture is _______ kg/m3
A 1.8-m3 rigid tank contains steam at 220°С. One-third of the volume is in the liquid phase and the rest is in the vapor form. Determine (a) the pressure of the steam, (b) the quality of the saturated mixture, and (c) the density of the mixture.
A piston–cylinder device initially contains 0.6 m3 of saturated water vapor at 250 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 300 kPa is required to move it. Heat is now slowly transferred to the steam until the volume becomes 1.5 m3. Use the data from the steam tables. a) Determine the final temperature. b) Determine the work done during this process. c)...
Thermodynamics A piston-cylinder system contains 0.005 m3 of liquid water and 0.8 m3 of water vapor in equilibrium at 600 kPa. Heat is transferred at constant pressure until the temperature reaches 200ºC. a- Determine the initial thermodynamic state of the system. b- Find the initial temperature of water. c- Calculate the total mass of water in the cylinder. d- Find the final volume of the system. e- Sketch the above thermodynamic process on a P-V phase diagram.
A 160 m3 rigid tank is filled with saturated liquid-vapor mixture of water at 50oC. 70% of the mass is vapor and the 30% of the mass is liquid. The mixture is then heated until its pressure is 50kPa. Determine the final temperature(oC).
A rigid vessel with a total internal volume of 0.10 m3 contains saturated H2O at a pressure of 1.0 MPa. If the volumes of liquid and vapour are 0.04 m3 and 0.06 m3 respectively, what is the dryness fraction? --
A 0.3 m3 rigid tank is filled with saturated liquid water at 200°C. A valve at the bottom of the tank is opened, and liquid is withdrawn from the tank. Heat is transferred to the water such that the temperature in the tank remains constant. Determine the amount of heat that must be transferred by the time 2 of the total mass has been withdrawn. a. Hint: The phase of the water when / of the mass has exited is...
Required information A piston-cylinder device initially contains 0.6 m3 of saturated water vapor at 250 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 300 kPa is required to move it. Heat is now slowly transferred to the steam until the volume becomes 1.3 m3. Use the data from the steam tables. Determine the final temperature. (You must provide an answer before moving on...
A rigid tank having a volume of 0.1 m3 initially contains water as a two-phase liquid-vapor mixture at 1 bar and a quality of 1%. The water is heated in two stages: Stage 1: Constant-volume heating until the pressure is 20 bar. (treat as closed system) Stage 2: Continued heating while saturated water vapor is slowly withdrawn from the tank at a constant pressure of 20 bar. (Note: Use transient analysis with all the water leaving having a quality of...