Problem 1.1 A hollow cylindrical tube is going to be subjected to a 10,000 lb tension...
A hollow shaft consisting of a steel tube of 50-mm outer diameter is to transmit 250 kW of power while rotating at a frequency of 30 Hz. Determine - (7 points) (a) the tube thickness that should be used if the shearing stress is not to exceed 100 MPa. (3 points) (b) since in this simplified design calculation, the only stress considered is shear stress exerted on the shaft due to torques. Without taking into account of how power is...
Assume the crane is made of squared tube that has 1 inch height,
1 inch width, and 1/16 inch thickness. One side of the rope is
attached to a 50 lb load, while the other side is fixed to the
vertical member. Assume the weight of the pulley is negligible, and
its surface is frictionless.
1- Find the stress at point A
2- Find the stress at point B
Assume Modulus of Elasticity = 10,000 ksi and Poisson’s Ratio =...
P Problem 3 (30 pts): Combined Loading A pressurized cylindrical air tank is subjected to a force P at a collar B. The tank has an inner diameter (d= 160 mm) with wall thickness (t = 6 mm). The gage pressure inside the tank is p = 5 MPa and the applied force is P=9.5 kN. B 450 mm (a) Determine the maximum tensile stress 0 [MPa], maximum compressive stress oc [MPa] and maximum shear stress Tmax [MPa] at point...
P B Problem 3 (30 pts): Combined Loading A pressurized cylindrical air tank is subjected to a force Pat a collar B. The tank has an inner diameter (d = 160 mm) with wall thickness (t = 6 mm). The gage pressure inside the tank is p = 5 MPa and the applied force is P=9.5 kN. (a) Determine the maximum tensile stress o [MPa], maximum compressive stress oc [MPa] and maximum shear stress Tmax [MPa] at point a. (b)...
Will RATE!!!
Calculate the tensile stress hoop and longitudinal developed in the walls of a cylindrical pressure vessel. The inside diameter is 18 inch. The wall thickness is k inch.The vessel is subjected to an internal gage pressure of 300 psi and a simultaneous external axial tensile load of 50,000 lb. 4.A V-belt with a groove angle 40 has a max belt tension 150 lb on the tight side and 75 lb on the loose side. If the coefficient of...
Problem # 2(7 points) hollow steel tube having external and internal diameter of 100 mm and 75 mm respectively is simply supported over a span of 5 m. The tube car concentrated load of W at a distance of 2 m from of the supports. What is the value of W, if the maximum bending stre if the maximum bending stress is not to exceed 100 MPa
An alumninum (E = 68.9 GPa) cylindrical tube has an outer diameter of 200 mm, a wall thickness of 7.5 mm, and an internal pressure of 5 MPa. It is subjected to a force with the axial and transverse components shown acting at the centroid of the free end of the tube 1. Verify that the tube meets the thin-wall criterion 2. Draw the left half of the tube, and show the equivalent force-couple system acting at the centroid of...
Hello, please help me with this homework problem. Please show
all work. (Correct answers are listed at the bottom)
Homework Assignment #33 10 points The University of Akron Department of Civil Engineering 4300 202: Introduction to Mechanics of Solids 1. A solid tube is subjected to the loading shown. The tube has a diameter of 1.5 in. 8 in. (a) Determine which internal force quantities would cause normal stresses and which would cause shear stresses on a cross-section cut through...
Problem 2: (34 pts) For the cylindrical tube (outer radius R. 100mm, initial thickness 1mm before loadings, length 1m) fixed at one end on the wall, an axial loading F = 1000 N and a torsional loading T = 100 N-m are applied. Assuming linear elasticity. Young's modulus E-1 GPa and Poisson ratio v = 0.33. (T = **where ) = (R: - R ) is the polar moment of inertia) a) Calculate the stress state (Cro, and Try) of...
Problem 9.72 Review The thin-walled pipe has an inner diameter of 0.5 in and a thickness of 0.025 in Part A Figure 1 of 1 It is subjected to an internal pressure of 416 psi and the ancial tension and forsional loadings shown, determine the principal stress at a point on the surface of the pipe. (Figure 1) Enter your answers numerically separated by a comma. | ΑΣΦινος ? 010 31.398, 20,308 ksi 200 lb 200 Submit Previous Answers Request...