A 25kg sphere is balanced on top of a table. The sphere covers an area of...

Question

Question

A 25kg sphere is balanced on top of a table. The sphere covers an area of 10m2. What is the pressure applied to this table ?

Answer 1

Answer #1

The pressure is given by:

$P = \frac{F}{A}= \frac{25*9.8}{10} = 24.5 Pa$

Answer 2

Similar Homework Help Questions

Find the liquid pressure at the bottom of a 50m deep container that carries ethyl alcohol....

Find the liquid pressure at the bottom of a 50m deep container that carries ethyl alcohol. For the following problem, assume a constant temperature. With an initial pressure of 500pa, what is the final pressure inside a container after it undergoes a volume change from 10 m^3 to 2m^3? A 25kg sphere is balanced on top of a table. The sphere covers an area of 10m^2. What is the pressure applied to this table? Draw the electric field lines between...
A block of mass .5kg is ona table and attached to a block of mass .25kg...

A block of mass .5kg is ona table and attached to a block of mass .25kg by a taut massless string. The .25kg block hangs by means of the string, which goes over a pulley. The .25kg block is released, and it descends from rest at a constant acceleration, travelling 1.00m in 1.25s. What is the coefficient of kinetic friction between the table and the .5kg block?
1. Sphere 1 has surface area A1 and volume V1 and sphere 2 has surface area...

1. Sphere 1 has surface area A1 and volume V1 and sphere 2 has surface area A2 and volume V2. If the radius of sphere 2 is 3.86 times the radius of sphere 1, what is the ratio of the areas A2/A1? 2. What is the ratio of the volumes V2/V1

Sphere 1 has surface area Ai and volume Vi and sphere 2 has surface area A2...

Sphere 1 has surface area Ai and volume Vi and sphere 2 has surface area A2 and volume V2. If the radius of sphere 2 is 1.84 times the radius of sphere 1, what is the ratio of the areas A2/A1? Tries 0/8 What is the ratio of the volumes V2/V1? Tries 0/8 Submit Answer Submit An Post Discussion Sen
Sphere 1 has surface area A1and volume V1, and sphere 2 has surface area A2and volume...

Sphere 1 has surface area A1and volume V1, and sphere 2 has surface area A2and volume V2. If the radius of sphere 2 is 9times the radius of sphere 1, what is the ratio of each of the following? (a) the areas, A2/A1 (b) the volumes, V2/V1
A small circular surface of area A 2cm located at the center of a 2-m-diameter sphere emits radia...

A small circular surface of area A 2cm located at the center of a 2-m-diameter sphere emits radiation as a blackbody at T 1000 K. Determine the rate at which radiation energy is streaming through a D-1-cm-diameter hole located (a) on top of the sphere directly above Ai and (b) on the side of sphere such that the line that connects the centers of A: and Az makes 45" with surface A A small circular surface of area A 2cm...

What is the total volume of the Ice sheet? It covers an area of 1,710,000 km2...

What is the total volume of the Ice sheet? It covers an area of 1,710,000 km2 with an average depth of 1.5 km.
A sphere with a mass of 8kg and diameter of 25cm is initially on top of...

A sphere with a mass of 8kg and diameter of 25cm is initially on top of a ramp at rest with an angle of 30 degrees with a base length of 5 meters. The sphere rolls down the ramp with an initial velocity of 3 m/s. a) What is the final velocity of the sphere at the bottom of the ramp if the coefficient of friction is 0.3 [I=2/5 mr^2] b) Calculate the revolutions per second of the sphere from...
(a) A sphere and a cylinder are released from the top of an inclined plane and roll without slipping to the bottom. Whi...

(a) A sphere and a cylinder are released from the top of an inclined plane and roll without slipping to the bottom. Which one gets there first? (explain your answer and show calculations) [2 Marks] (b) What does it mean to say that an object is dynamically balanced? How is this different to an object being statically balanced? [1 Mark] (c) Under what conditions can we apply techniques from 2-dimensional (planar) rigid body mechanics to 3-dimensional objects? [1 Mark] (d)...

The top and bottom surfaces of a metal block each have an area of A =...

The top and bottom surfaces of a metal block each have an area of A = 0.025 m2, and the height of the block is d = 0.12 m. At the top surface of the block, a force F1 is applied to the right, while at the bottom surface of the block, a force F2 is applied to the left, causing a shear in the metal block. If F1 = F2 = 41 ✕ 106 N and the displacement between...