Homework Answers
Add Answer to:
the a average is 2.00 x 10-5
3. The outer diameter of the tubes is 5/8"...
Thin-walled aluminum tubes of diameter D = 10 mm are used in the condenser of an air conditioner....
Thin-walled aluminum tubes of diameter D = 10 mm are used in the condenser of an air conditioner. Under normal operating conditions, a convection coefficient of hi = 5000 W/m2 · K is associated with condensation on the inner surface of the tubes, while a coefficient of ho = 100 W/m2 · K is maintained by airflow over the tubes. a. What is the overall heat transfer coefficient if the tubes are unfinned? b. What is the overall heat transfer...
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of...
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is attached to the wall at point A and three torques are applied as shown, determine the minimum shear stress developed in the pipe. Answers should be given in units of MPa. 30 N m 20 N m 80 N m For the 30mm diameter shaft shown below made of steel (G-200GPa), what is the magnitude of the total angle of...
4. A pure copper pipe with inner diameter Di-10 mm ard outer diameter Do-14 mm is surrounded by s...
4. A pure copper pipe with inner diameter Di-10 mm ard outer diameter Do-14 mm is surrounded by saturated steam with pressure p 172 bar and convection coefficient h 6000 carries water with mean velocity u- (a) Determine the convective heat transfer coefficient inside the pipe for water at mean temperature Tm 37° C (b) At this same location, determine the total thermal resistance (per unit length) between the water and the steam. (c) Determine the heat transfer rate (per...
3. A cooling system uses 8 copper cylindrical fins of diameter 6 mm and length 100...
3. A cooling system uses 8 copper cylindrical fins of diameter 6 mm and length 100 mm to dissipate heat. The surface around the fins is maintained at 150 °C, and the tips of the fins are insulated. Air at 50 °C is used to cool the fins, flowing at 5 m/s. The flows around the fins do not affect each other. (a) Determine the average convection coefficient around each fin. (b) Calculate the overall heat dissipation rate of the...
Calculate initial concentration of Fe+3 for tubes 1-3. Show your work. Procedure A. Determination of B...
Calculate initial concentration of Fe+3 for tubes 1-3. Show your
work.
Procedure A. Determination of B for Beer's Law 1. Using a buret, add 4.00 mL of 0.0025 M Fe(NO3)s (which is in 0.1 M HNOs) to a 100- mL volumetric flask. Add enough deionized water to bring the total volume to the mark on the neck of the flask. Stopper and shake the flask. Label this flask “Diluted Fe.” spectrophotometer tubes (cuvettes), they are too small to use at...
3. A beam with a hollow circular cross section of outer diameter D and inner diameter...
3. A beam with a hollow circular cross section of outer diameter D and inner diameter d. The length Lis fixed at a wall. Consider the following loading conditions, all applied to the beam at the midpoint of length L. For each loading scheme state determine the magnitude of that stress in terms of the variables given in the problem). (5 points) i. ii. iii. iv. V. Normal stress due to axial load F Shear stress due to torque T...
PROBLEM 3 (45 points) The condenser of a large steam power plant is a heat exchanger...
PROBLEM 3 (45 points) The condenser of a large steam power plant is a heat exchanger in which steam is condensed to liquid water. Assume the condenser to be a parallel flow shell-and-tube heat exchanger consisting of a single shell and 1x10 tubes, each executing two passes. The inner diameter of tubes is D = 50 mm and its thickness is 5 mm (Do not ignore the thickness). The steam condenses on their outer surface. Thermal conductivity of the tube...
Water at an average velocity of 3.5 m/s flows through a 5-m-long stainless steel tube (k...
Water at an average velocity of 3.5 m/s flows through a 5-m-long stainless steel tube (k = 14.2 W/m °C) in a boiler. The inner and outer diameters of the tube are Di = 1.0 cm and Do = 1.4 cm, respectively. If the convection heat transfer coefficient at the outer surface of the tube where boiling is taking place is ho = 8400 W/m2 • °C, determine product of the overall heat transfer coefficient Ui by the inner surface...
Q1: Heated air at 1 atm, 100F, and 23% relative humidity is to be transported in...
Q1: Heated air at 1 atm, 100F, and 23% relative humidity is to be transported in a 490 ft long circular plastic duct at a rate of 740 cfm (ft 3 /min). If the head loss in the duct is not to MEC_AMO_TEM_034_01 Page 1 of 8 Design of Thermal System (MECH 0009) - Spring-2020 -Assignment 2- A&B - QP exceed 790 in. of air, determine the minimum diameter of the duct. (Hint: initial guess value for the diameter is...
A wire 50.0 m long 려nd 2.00 mm in diameter is connected to a source with...
A wire 50.0 m long 려nd 2.00 mm in diameter is connected to a source with potential difference of 9.11 V, and the current is found to be 5.72 A. Assume a temperature of 20°C and using the table below, identify the metal out of which the wire is mad Resistivities and Temperature Coefficients of Resistivity for Various Materials (at 20°c) Material Resistivity Temperature Coefficient (Q m)of Resistivity (°c)-1 -3 1.59× 10 3.8 x 10 1.7 x 10-8 2.44 x...
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is attached to the wall at point A and three torques are applied as shown, determine the minimum shear stress developed in the pipe. Answers should be given in units of MPa. 30 N m 20 N m 80 N m For the 30mm diameter shaft shown below made of steel (G-200GPa), what is the magnitude of the total angle of...
4. A pure copper pipe with inner diameter Di-10 mm ard outer diameter Do-14 mm is surrounded by saturated steam with pressure p 172 bar and convection coefficient h 6000 carries water with mean velocity u- (a) Determine the convective heat transfer coefficient inside the pipe for water at mean temperature Tm 37° C (b) At this same location, determine the total thermal resistance (per unit length) between the water and the steam. (c) Determine the heat transfer rate (per...
3. A cooling system uses 8 copper cylindrical fins of diameter 6 mm and length 100 mm to dissipate heat. The surface around the fins is maintained at 150 °C, and the tips of the fins are insulated. Air at 50 °C is used to cool the fins, flowing at 5 m/s. The flows around the fins do not affect each other. (a) Determine the average convection coefficient around each fin. (b) Calculate the overall heat dissipation rate of the...
Calculate initial concentration of Fe+3 for tubes 1-3. Show your
work.
Procedure A. Determination of B for Beer's Law 1. Using a buret, add 4.00 mL of 0.0025 M Fe(NO3)s (which is in 0.1 M HNOs) to a 100- mL volumetric flask. Add enough deionized water to bring the total volume to the mark on the neck of the flask. Stopper and shake the flask. Label this flask “Diluted Fe.” spectrophotometer tubes (cuvettes), they are too small to use at...
3. A beam with a hollow circular cross section of outer diameter D and inner diameter d. The length Lis fixed at a wall. Consider the following loading conditions, all applied to the beam at the midpoint of length L. For each loading scheme state determine the magnitude of that stress in terms of the variables given in the problem). (5 points) i. ii. iii. iv. V. Normal stress due to axial load F Shear stress due to torque T...
PROBLEM 3 (45 points) The condenser of a large steam power plant is a heat exchanger in which steam is condensed to liquid water. Assume the condenser to be a parallel flow shell-and-tube heat exchanger consisting of a single shell and 1x10 tubes, each executing two passes. The inner diameter of tubes is D = 50 mm and its thickness is 5 mm (Do not ignore the thickness). The steam condenses on their outer surface. Thermal conductivity of the tube...
Water at an average velocity of 3.5 m/s flows through a 5-m-long stainless steel tube (k = 14.2 W/m °C) in a boiler. The inner and outer diameters of the tube are Di = 1.0 cm and Do = 1.4 cm, respectively. If the convection heat transfer coefficient at the outer surface of the tube where boiling is taking place is ho = 8400 W/m2 • °C, determine product of the overall heat transfer coefficient Ui by the inner surface...
Q1: Heated air at 1 atm, 100F, and 23% relative humidity is to be transported in a 490 ft long circular plastic duct at a rate of 740 cfm (ft 3 /min). If the head loss in the duct is not to MEC_AMO_TEM_034_01 Page 1 of 8 Design of Thermal System (MECH 0009) - Spring-2020 -Assignment 2- A&B - QP exceed 790 in. of air, determine the minimum diameter of the duct. (Hint: initial guess value for the diameter is...
A wire 50.0 m long 려nd 2.00 mm in diameter is connected to a source with potential difference of 9.11 V, and the current is found to be 5.72 A. Assume a temperature of 20°C and using the table below, identify the metal out of which the wire is mad Resistivities and Temperature Coefficients of Resistivity for Various Materials (at 20°c) Material Resistivity Temperature Coefficient (Q m)of Resistivity (°c)-1 -3 1.59× 10 3.8 x 10 1.7 x 10-8 2.44 x...
Most questions answered within 3 hours.
-
A construction company is planning to bid on a building
contract. The bid costs the company...
asked 6 minutes ago -
A sample of 45 observations is selected from a normal
population. The sample mean is 49,...
asked 9 minutes ago -
A firm operating in a purely competitive environment is faced
with a market price of $250....
asked 13 minutes ago -
•Let’s say someone claims the average population size is
600 feet squared and the housing authority...
asked 20 minutes ago -
Cynaide is a deadly poison that blocks the last step in the
electron transport chain of...
asked 24 minutes ago -
Your friend tells you that there is a vending machine on campus
that dispenses M&M packs...
asked 40 minutes ago -
What advantages are there to using piperidine rather than
hydroxide as a base?
asked 38 minutes ago -
7. The life of a Freeze Breeze electric fan is normally
distributed with a mean 4...
asked 41 minutes ago -
1. A 751 mL NaCl solution is diluted to a volume of 1.06 L and a...
asked 46 minutes ago -
8
A $20,000 face value STRIPS is currently quoted at 38.642 and
has 8 years to...
asked 46 minutes ago -
The current exchange rate between the Japanese yen and
the US dollar is 120 yen per...
asked 48 minutes ago -
Marla’s Massages and More bought a special massage table two
years ago for $9,300. At the...
asked 56 minutes ago