Grade: Problem 1. Draw both the x component and y component of force P1 in the...
1.) Find the x-component and y-component of the total force
exerted on the third charge by the other two.
2.) What is the magnitude of the total force acting on the third
charge.
3.) What is the direction of the total force acting on the third
charge.
A charge 4.99 nC is placed at the origin of an xy-coordinate system, and a charge -1.98 nC is placed on the positive x-axis at x = 3.96 cm . A third particle,...
Problem 4: For the fixed-fixed beam shown below, a) Sketch the shear force and bending moment diagrams. Consider P1 = 10 kips, P2 = 15 kips, and w = 2 kips/ft. b) Indicate the values of maximum positive and negative bending moments and specify the location of these maximum values along the beam. (You are allowed to refer to the attached AISC Table for appropriate formulations or use any software) P2 TTTTTTTTTTTTTTT 6 ft. 1 0ft. t 4 ft.
Quiz # 1 Name: Decompose the force F and determine its components in x direction and y direction, as well as their signs corresponding to the coordinate system for each case shown below. Date: F=110 kips a =45°
blem 2. (70 points) 1. For the beam shown in Figure (a): a) b) draw the shear force and bending moment diagrams. (30 points) Select the most economical W shape for the beam with an allowable bending stress of 30 ksi. (10 points) determine the maximum tensile and compressive bending stresses at any location along the beam if the section shown in Figure (b) is used instead of the W shape section selectedin Part b. Would the beam be safe...
HUNO Quce hinh qu ww 1852422 HS P1 PROBLEMS: Di mele of an ideal gas follows the e cess and 3-1 is isobaric is isoch are eiven; Va2V1 , P2- Pi/3. Determine (according to P1, VI): the figure. 1-2 wn a) Adiabatic co Y and molar specific heats Cv and Cp h) The beats from 1-2 and 3-1 processes? c) The thermal efficiency of the engine operating with this cycle. .. P2 V2 V1 2. Two point charges of SpC...
Problem 1 F d L B A CO 30° с x F F = 53 lb L = 11.3 in d = 1.5 in The pliers shown are used to grip a 0.3-in.-diameter rod. Knowing that two 53-1b forces are applied to the handles, 1- Determine the magnitude of the forces exerted on the rod by each portion of the pliers in lb. Answer: 339.26 X 2- Determine the x-component of the force exerted by the pin at A on...
1) Draw the gravitational acceleration (g—>) and its
component vectors in the coordinate system shown above and label
them.
2) Express g—> in its component form according to the
coordinate system.
Problem 1 Determine the reactions at the supports and the force in all the members of the truss, indicate whether the force is in tension or compression. The values shown apply. Drawing Not to Scale P1 T . . . a | 4 m | P1 | 2,000 N 5 m P2 4,000 N C 3 m нь
determine the X component of reaction at A
determine the Y component of reaction at A
determine the Xcomponent of reaction at D
determine the Y component of reaction at D
CHW 5 -Force Method Problem 9.23 - Enhanced with Hints and Feedback Consider the trave shown in Figure 1). Assume A and Dare pins BT is constant Suppose that 1.8k/t. Part A Determine the component of reaction at Express your answer using three significant figures. View Available in ΑΣ...
Consider a problem with seven items whose weight and values are given below. w1, w2,.., W7 (40, 50, 30, 10, 10, 40, 30) p1, p2,.,, p7 (40, 60, 10, 10, 3, 20, 60) The total allowable weight in the knapsack w = 100, solve this problem using backtracking and draw a complete DFS tree.
Consider a problem with seven items whose weight and values are given below. w1, w2,.., W7 (40, 50, 30, 10, 10, 40, 30) p1, p2,.,, p7...