YYCH 22 If a Δν ax : 220 V power source is placed across a resistor...
If a Delta V_max = 115 V power source is placed across a resistor and the resulting current through the resistor is I_max = 1.6 A, what is the resistance? 63.34 ohms 71.88 ohms 80.24 ohms 75 76 ohms 88.93 ohms 72.28 ohms
A 98-W lamp is placed in series with a resistor and a 120-V source. If the voltage across the lamp is 30 V, what is the resistance R of the resistor?
A resistor is placed in a circuit with an adjustable voltage source. The voltage across and the current through the resistor and the measurements are shown below. Estimate the resistance of the resistor (in 12). Voltage (V) 3000F 2400 1800 1200 600 Current (A) 10 2 4 6 8 X 12 Enter a number.
A 67 Vrms source is placed across a load that consists of a 12 ohm resistor in series with an capacitor whose reactance is 5 ohms. Compute the following: a) The average power of the load b) The reactive power of the load c) The apparent power of the load d) The power factor of the load
2. An AC power source with V 220 V and f60.0 Hz is connected in a series RLC circuit. The resistance, R. inductance, L, and capacitance. C. of this circuit are, respectively. 46.0 12, 0.150 H. and 0.035 mF. Find each of the following quantities, (a) the inductive reactance, the capacitive reactance, (c) the impedance of the circuit (d) the maximum current through the circuit (based on the frequency given above) (e) the maximum potential difference across each circuit element...
1. A resistor R and capacitor care connected in series with an AC voltage source with frequency f and maximum voltage Vo. a. Find the complex impedance (in the form Z = R + jX). If the impedance is written in polar form (Z = Zejº), find expressions for Z and Ⓡ. Write your answers in terms of the variables R, C, and o(= 21f). b. If the voltage source is described by the phasor V = V, ejwt, and...
Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...
1. Why can the DSO only measure node voltages when the Function Generator is the power supply in a circuit (unless it is using a current probe)? 2. Consider Figure 1. According to the calculations in the lab handout, if Z-1kΩ +/6914, then the phase difference (фи-фі) between u(t) and i (t) is 34.6". a. If this v(t) and i(t) were displayed on a DSO (v(t) being a node voltage and using a current probe for i(t) as shown in...
I need a help with my lab, I write all data that get. 355 SERIES SINUSOIDAL CIRCU CUITS neeseed 000 10 mH 10 kHz + R E-8V(Pp) V 1 kn Channel 2 Vert: 1 Vidiv Hor: 20 us/div. Channel 1 Vert: 1 Vidiv Hor: 20 us/div. FIG. 9.1 (b) After setting E to 8 V (p-p), determine the peak-to-peak voltage for Ve from chan- nel 2 and record in the top row of Table 9.1 Determine the phase angle 8,...