***Please Use Empirical Units*** A roller chain no. 60 drives an output sprocket at 300 rpm....
***Please Use Empirical Units***
A roller chain no. 60 drives an output sprocket at 300 rpm. The
input sprocket has 15 teeth and the output sprocket has 21 teeth.
Determine the
a) diameter of each sprocket,
b) input speed in rpm,
c) chain speed in ft/min,
d) power rating for the chain, and
e) type of lubrication.
Homework Answers
Add Answer to:
***Please Use Empirical Units***
A roller chain no. 60 drives an output sprocket at 300 rpm....
***Please Use Empirical Units*** Consider a chain-and-sprocket speed reducer with chain no. 60. The objective is...
***Please Use Empirical Units*** Consider a chain-and-sprocket speed reducer with chain no. 60. The objective is to drive the load at 200 rpm using a motor that rotates at a constant speed of 300 rpm and supplies a torque of 400 in-lbs. Assume that the input sprocket has 20 teeth. a) For the input and output sprockets, specify the pitch, number of teeth, and pitch diameters. b) How much torque is available at the output shaft? c) How much power...
5 kW of power will be transmitted via a chain-sprocket system. The rotational speed of input...
5 kW of power will be transmitted via a chain-sprocket system. The rotational speed of input shaft is 20 rpm. The required approximate rotational speed of the input shaft is 20 rpm. Required approximate rotational speed for the out shaft is 7 rpm. The approximate distance between center lines of input and output shafts should be 900 mm. This chain-sprocket system is used for an elevator and it is asked to use a single or multiple DIN 8187 chain with...
Driver Type: Steam Turbine Input Power: 25 hp Use multi strand: 2 Driven Machine: Centrifugal Pump...
Driver Type: Steam Turbine Input Power: 25 hp Use multi strand: 2 Driven Machine: Centrifugal Pump Input Speed: 1900 rpm Nominal output Speed: varies between 770 and 780 rpm Specify the chain number and chain size, the sizes and number of teeth on each sprockets, The number of chain pitches, maximum center distance, chain length, Angles of wrap, Sprockets diameter, Type of lubrication
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shaft...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Desgin 0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Please help. Thx Part 2 (50 pts) A single-reduction spur gear system is as shown. The pinion "P" drives gear "G. Pinion"Pis driven at 1800 rpm with 1.5 hp Pinion "P" has a...
Please help.
Thx
Part 2 (50 pts) A single-reduction spur gear system is as shown. The pinion "P" drives gear "G. Pinion"Pis driven at 1800 rpm with 1.5 hp Pinion "P" has a pitch diameter of 2 inches, and has 20 teeth. The gear "Ghas 120 teeth. All teeth have a pressure angle of 20, full-depth, hobbed profile, and a face width of 0.5 inches. All materials are steel. Determine: A) Minimum number of pinion teeth: Np,min This shows that...
find v belt drive design power select belt type determine shive size (belt speed 4000 ft/min)...
find v belt drive
design power
select belt type
determine shive size (belt speed 4000 ft/min)
find shive size from power rating figure
find rated power
find estimated centre distance
find belt length (by selecting standard belt length)
calculate actual centre distance
find contact angle for small shieve
determine correct factors
calculate correct power per belt
no. of belt needed
V-Belt Designing Sample Problem . Given: A 4 cylinder diesel engine runs at 80 hp, 1800 rpm, to drive a...
You are the designer and you have been asked to design a speed reducer (gearbox) that will take p...
power = 3 kW
if need any more information please ask !!!
You are the designer and you have been asked to design a speed reducer (gearbox) that will take power from the shaft of an electric motor rotating at 1500 rpm and deliver it to a machine that is to operate at approximately at 200 rpm Assume that you have decided to use spur gears to transmit the power [A power equal to the last one digits of your...
please answer as many as possible 11, A water-cooled electric power plant generates 300 MW of...
please answer as many as possible
11, A water-cooled electric power plant generates 300 MW of power at efficiency of 35%. At what rate must water be circulated past the condenser if the change in water temperature is not to exceed 20 C? (The specific heat of water is 4.2 x ios J/kg°C) A) E) 14000 x 10 kg/s 7000x10 kg/s 21000 x103 kg/s B) 6000 × 103 kg/s C) D) 4000 x1OP kg/s 12. A generator operates between a...
Please complete all work in excel. Use excel to make the calculations (cells can be clicked...
Please complete all work in excel. Use excel to make the calculations (cells can be clicked on to view any formulas used) and be sure to identify your answer, including units. Upload one excel file for your submission. Delights Company is designing a production layout for a new product. They plan to use this production line 10 hours a day in order to meet forecasted demand of 80,000 units per day. For output to equal forecasted demand, what should the...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Desgin
0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
Please help.
Thx
Part 2 (50 pts) A single-reduction spur gear system is as shown. The pinion "P" drives gear "G. Pinion"Pis driven at 1800 rpm with 1.5 hp Pinion "P" has a pitch diameter of 2 inches, and has 20 teeth. The gear "Ghas 120 teeth. All teeth have a pressure angle of 20, full-depth, hobbed profile, and a face width of 0.5 inches. All materials are steel. Determine: A) Minimum number of pinion teeth: Np,min This shows that...
find v belt drive
design power
select belt type
determine shive size (belt speed 4000 ft/min)
find shive size from power rating figure
find rated power
find estimated centre distance
find belt length (by selecting standard belt length)
calculate actual centre distance
find contact angle for small shieve
determine correct factors
calculate correct power per belt
no. of belt needed
V-Belt Designing Sample Problem . Given: A 4 cylinder diesel engine runs at 80 hp, 1800 rpm, to drive a...
power = 3 kW
if need any more information please ask !!!
You are the designer and you have been asked to design a speed reducer (gearbox) that will take power from the shaft of an electric motor rotating at 1500 rpm and deliver it to a machine that is to operate at approximately at 200 rpm Assume that you have decided to use spur gears to transmit the power [A power equal to the last one digits of your...
please answer as many as possible
11, A water-cooled electric power plant generates 300 MW of power at efficiency of 35%. At what rate must water be circulated past the condenser if the change in water temperature is not to exceed 20 C? (The specific heat of water is 4.2 x ios J/kg°C) A) E) 14000 x 10 kg/s 7000x10 kg/s 21000 x103 kg/s B) 6000 × 103 kg/s C) D) 4000 x1OP kg/s 12. A generator operates between a...
Most questions answered within 3 hours.
-
Given the pKa values of Lysine (2.2, 9.0 and 10.5), what is
the net charge of...
asked 8 seconds ago -
Which of the following descriptions of correlation is
correct?
Group of answer choices
a) Correlation equals...
asked 1 minute ago -
Which of the following answers complete the sentence
correctly?
The pyruvate dehydrogenase complex is activated by:...
asked 2 minutes ago -
On the first day of the fiscal year, a company issues a
$920,000, 9%, 5-year bond...
asked 9 minutes ago -
Compute the illumination at the edge of a circular table of
radius of 1 m, if...
asked 10 minutes ago -
A 66 kg water skier is being accelerated by a ski boat on a flat
("glassy")...
asked 9 minutes ago -
Recently I purchased a second vehicle for our family. The
vehicle we had was too small...
asked 18 minutes ago -
Two narrow, parallel slits separated by 0.850 mm are illuminated
by 570-nm light, and the viewing...
asked 26 minutes ago -
Write a balanced equation for the double-replacement
precipitation reaction described, using the smallest possible
integer coefficients....
asked 25 minutes ago -
Would You expect the analysis produced by the Legislative
Analyst’s Office to be more or less...
asked 42 minutes ago -
How configuring websites to use a common NFS share could
strengthen business continuity efforts
asked 43 minutes ago -
Arrange the following aqueous solutions in order of increasing
boiling point: 0.25 m NaCl (sodium chloride)...
asked 43 minutes ago