(30%) 2. A hollow circular steel member with outside and inside diameters 150 mm and 120...
A hollow circular steel shaft has a 100-mm outside diameter and a 75-mm inside diameter. Calculate the allowable torque that can be transmitted if the allowable shear stress is 62 MPa. When the allowable torque is applied, calculate the shear stress at the inner surface of the shaft.
Consider a hollow aluminium tube. The outside diameter is 110 mm and inside diameter is unknown The tube must carry a tensile load of 450 kN. Determine the inside diameter of the tube if the allowable normal stress is 175 MPa. Make a sketch of the tube showing the load and list all the steps of the solution.
please answer 18.11 and 18.12 18.11 A steel ring with an outside diameter of 150 mm and an inside diameter of 100 mm is shrunk onto another steel ring with an inside diameter of 50 mm. An axial force of 56,54 kN is needed to push the rings apart. Calculate the pressure at the mating surface and the shrinkage allowance given that both rings are 20 mm thick and the coefficient of friction between the mating surfaces is 0,2. Using...
Q.3. A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is fixed at ends A and B. Horizontal forces P are applied at the ends of a vertical arm that is welded to the shaft at point C. The allowable shear stress in the shaft is tall 45 MPa. Determine the maximum allowable force P 200 mm 200 mm 600 mm 400 mm
A 49 in long simply supported hollow circular steel tube has a 1.68 in OD and 0.392 in wall thickness. The cross-section is shown below. Use an allowable bending stress of 1.022 kpsi for steel and find the maximum safe uniformly distributed load that the beam can carry, if the loading is in the direction. Maximum safe uniformly distributed load- lbf/in.
the hollow tube down has an outside diameter of 45 mm and an inside diameter of 40 mm. the tube is made of an aluminum alloy with a minimum yield strength of 280 MPa. the bending load is F =1.5 kN, the axial load is P = 10kN and the twisting moment is T = 70 N-m. Determine the factor of safety based on the stress at point A using (a) the maximum shear stress theory and (b) the distortion...
01. Shaft BC is hollow with inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and CD are solid and of diameter d. For the loading shown, determine (a) the maximum and minimum shearing stress in shaft BC, (b) the required diameter d of shafts AB and CD if the allowable shearing stress in these shafts is 65 MPa. [TA = 7.5 kNm; TB = 16 kNm; TC = 30 kNm; TD = 7 kNm] 01....
Problem 1 (33 pts) The hollow shaft of inside diameter 8 mm, outside diameter 12 mm, L - 1.2 m, and shear modulus G = 80 GPa is subjected to T. Shear stress Txy at point A located at the outside of the shaft was found to be 48.96 MPa. Find the rotation of the shaft at its free end (where T' is applied) in degrees. For a circular cross section of diameter d, the polar moment of inertia is...
10.21 A steel compression member of 2.75-m effective length supports an eccentric load as shown. Using the allowable-stress method and assuming e 40 mm, determine the load P. Use ơr 250 MPa and E 200 GPa. with that 40 mm S130 x 15 Fig. P10.21 60 mm. 10.22 Solve Prob. 10.89 using e
160 mm 10 mm A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 and 60 mm. The allowable shearing stress is 120 MPa with a modulus of rigidity (shear modulus) G-77 GPa, assuming fully elastic deformation. (a) What is the largest torque that can be applied to the shaft? (5 points) (b) What is the corresponding minimum value of the shearing stress in the shaft? (5 points) (c) What are...