in postion 1. position 2, and postoa 3. in the circuit given below. R.-13kD, R2 ....
3. Find it) for t-0 in the circuit below: R2 2k2 itn 6M 3 ? 200 F Vs MATLAB code: Complete code then run it clc; clear all; close all; ;RI-- :R2+, %declare values C: %when switch is closed,find differential equation with syms t ;Vs- ; %when switch open ;R3 a-
3. UMF 5.33 5.33 After having been in position 1 for a long time, the switch in the circuit of Fig. P5.33 was moved to position 2 at t = 0. Given that Vo = 12 V, Ri = 30 k2, R2 = 120 KS2. R3 = 60 k-2, and C = 100 F, determine: (a) ic(0) and uc(0) (b) ic(O) and vc(0) (c) cic() and uc(0) (d) vci) for 10 (e) ic(t) for 1 > 0 i o e...
please show all steps In the circuit below, the switch has been open for a while. Given the values below, what is the time constant after the switch closes at t-0? Note: Enter your answer in millisecond and three decimals R,-3-k. R2-7-kN.R3=9-k2,C=2-4F V1-9-V, V2-3-V R3 R2 RI www www VI С 1=0
In the circuit below, all four resistors are identical (R1 = R2 = R3 = R4 = R) and the battery has a voltage of 4.92 V. (a) When the switch is placed in position 1, the measured current in the battery is 1.34 mA. What is the value of each resistor? k? (b) When the switch is placed in position 2, what is the current flowing out of the battery? mA (c) When the switch is open (neither in...
Question # 3 R1 100? S1 L1 2) Key Space R3 10mH R2 V1 For the circuit shown in the above figure, R3 is unkown: With the switch "S1" closed to position (2) and no currents in the circuit. The switch's position is changed from position (2) to position (1) at t-0. After a long time the circuit reaches a steady state condition. Calculate the steady state current in the inductance. 2) With the switch "S" closed to position (1)...
1. Response of the RL circuit - After having been in position 1 for a long time, the switch in the circuit below is moved to position 2 at the time t = 0. Given that Vo = 12 V, R1 = 3092, R2 = 12092, R3 = 6022 and L = 0.2 H, determine; a) iz(0-) and vi(0-) b) iz(0) and vi(0) c) il(o) and vi(0) d) il(t) for t20 e) vi(t) for t20 RU AN
Problem 1 (10 points): The switch in the circuit of Fig. 1 has been in position a for a long time. Att 0, the switch moves to position b 1. (4 points) Construct an s-domain circuit for t> 0 2. (4 points) Find Vo(s) and vo(t) for t> 0 3. (2 points) Find IL(s) and iL () fort > 0. t-0 Ri R2 R1 = 400 ohms, R2 = 1000 ohms, C = 6.25 nF L 16 mH, and vg-360...
Q2) The following figure shows an amplifier circuit and its parameters: Rc R. 0.1k R 100 R2-100k2 Ri 2 1 CL→0.1nF u Calculate all corner frequencies 2 Calculate the bandwidth of the amplifier circuit 3) Calculate the maximum voltage gain of the amplifier circuit in dB (Hint: assume Rsi 0) Page 1 of 2 Q2) The following figure shows an amplifier circuit and its parameters: Rc R. 0.1k R 100 R2-100k2 Ri 2 1 CL→0.1nF u Calculate all corner frequencies...
2) Shown below is a c R2 = 7 Ω, R3 = 24 Ω, R4 = 10 ircuit with two switches. Si and S2M = 15 V, V.-5 V, V,-20 V, Rı = 15 Ω . 25s2 C,200F v -,,I -R, Г 2:0 start atp sition A. This creates two dependent circuits. The left circuit with only resistors '5 V-15A)(T)-YAG).2ov-ocharges the capacitor C, through resistor Rs with battery Vs(the capacitor is initially The switch 1 will start in the on/closed...
The parameters of all elements in the circuit shown below are given: Ri=16.4 k22, R2=9.5 k12, C1=1.45 pF, C2=2.72 uF, and e=8 V (the internal resistance of the battery is negligible). R Hla E The capacitors in this circuit are not charged when, at time t=0, the switch S is closed. What is the current 11(t) in resistor R1 at time t=10.03 ms?: 11(t)= What is the charge Q2(t) on capacitor C2 at time t-10.03 ms?: Q2(t)- mA. ис.