A Steam Rankine Cycle receives fluid from a boiler at 3.5 MN/m2 and 350oC, exhausts to...
A Steam Rankine Cycle receives fluid from a boiler at 3.5 MN/m2 and 350oC, exhausts to the condenser at 10 kN/m2 and returns the condensate to the boiler via a feed pump.
Draw both the system showing plant layout and the cycle on a temperature/entropy graph.
Neglecting feed pump work calculate :-
- The energy supplied per kg of steam.
- The dryness fraction of the steam entering the condenser.
- The Rankine efficiency.
- The Ideal power output if the mass flow rate of the steam is 3000kg/Hr.
Homework Answers
Add Answer to:
A Steam Rankine Cycle receives fluid from a boiler at 3.5
MN/m2 and 350oC, exhausts to...
1. Ina Rankine cycle, steam leaves the boiler at 3.5 MPa 350oC. The condenser pressure is...
1. Ina Rankine cycle, steam leaves the boiler at 3.5 MPa 350oC. The condenser pressure is 10 kPa Determine the cycle efficiency. 150 points)
A steam power plant is based on the Rankine cycle with reheat (refer to the figure below). Steam ...
A steam power plant is based on the Rankine cycle with reheat (refer to the figure below). Steam is produced by the boiler/superheater (H-1) at 100 bar and 600 C at a rate of 2.5 kgs. This is expanded to 10 bar in the turbine T-1 and then reheated to 600 °C in heater H-2. The steam is then expanded in turbine T-2 to a pressure of 0.1 bar. The steam is then condensed in condenser (C-1) which operates at...
Question 5 1.5/3 points In a Rankine cycle, steam leaves the boiler and enters the ideal...
Question 5 1.5/3 points In a Rankine cycle, steam leaves the boiler and enters the ideal turbine at 6.9 MPala) as a saturated vapor. Condenser pressure is 6.9 kPaſa). The specific enthalpy of the subcooled condensate/feedwater at the discharge of the feedwater pump (h) is 166.36 kJ/kg. Identify the specific enthalpy (in kJ/kg) of the steam entering the turbine. 166.36 Calculate the quality (in %) of steam-water mixture leaving the turbine. Calculate the specific enthalpy (in kJ/kg) of the steam...
A steam power plant operates on the Rankine cycle modified to include superheat. The steam leaves...
A steam power plant operates on the Rankine cycle modified to include superheat. The steam leaves the superheater at a pressure of 40 bar and a temperature of 500oC. After expansion in the turbine, which has an isentropic efficiency of 82%, the steam exhausts into the condenser at a pressure of 0.2 bar. Neglecting feed pump work calculate :- 1. The Thermal Efficiency of the plant. 2. The specific steam consumption. 3. The required mass flow rate of steam if...
Tor steam power prants 4 marks D) A steam power plant is to be designed using the Rankine cycle with superheat. The...
Tor steam power prants 4 marks D) A steam power plant is to be designed using the Rankine cycle with superheat. The steam must enter; the turbine at pressure (P) and temperature (T), and the turbine steam exit pressure must be 0.05 bars. In order to produce 12 MW, a steam mass floW rate of 8.91 kg/s is to be used and the dryness fraction at turbine exit must be 0.9. Assuming the Rankine cycle to be ideal and neglecting...
P8-29 A closed feedwater heater is used in a Rankine cycle Steam leaves the boiler at...
P8-29 A closed feedwater heater is used in a Rankine cycle Steam leaves the boiler at 20 MPa, 600°C. Between the high and low-pressure turbines, steam at 1 MPa is extracted and delivered to the closed feedwater heater. Feedwater exits the feedwater heater at 20 MPa and the saturation temperature of the 1-MPa steam; saturated liquid condensate is fed through a steam trap back to the condenser. Steam from the second- stage turbine enters the condenser at 10 kPa, and...
8.12 Water is used as the working fluid in an ideal Rankine cycle. The steam is supplied as superheated steam at 30 bar,...
8.12 Water is used as the working fluid in an ideal Rankine cycle. The steam is supplied as superheated steam at 30 bar, 440°C. The condenser pressure is 0.5 bar. If isentropic efficiency of turbine and pump are 90% and 85%, respectively, determine the thermal efficiency of the cycle.
A Rankine Cycle based steam power plant produces 200 MW of power. Steam exits the boiler...
A Rankine Cycle based steam power plant produces 200 MW of power. Steam exits the boiler at 3 MPa and 500° C. The turbine exit is at 40 kPa. Isentropic efficiencies of the turbine and pump are 75% and 70% respectively. Show the cycle on a T-s diagram Calculate the mass flow rate of steam Determine the heat transfer rates in the boiler and condenser in MW Determine the cycle efficiency Determine the mass flow rate of the condenser cooling...
(15 pts.) In an ideal Rankine cycle that uses water as the working fluid. Superheated steam...
(15 pts.) In an ideal Rankine cycle that uses water as the working fluid. Superheated steam exits the boiler at 4 MPa and 600°C with a mass flow rate of 8 kg/s. The steam leaves the turbine at a pressure of 100 kPa. (a) Sketch the cycle on a T-s diagram (6) Determine the power output of the turbine (c) Determine the rate of heat loss from the condenser (d) The required pump power (e) The rate of heat addition...
(1) Q.5 (a) A power station using a Superheated Rankine cycle operates with a boiler pressure...
(1) Q.5 (a) A power station using a Superheated Rankine cycle operates with a boiler pressure of 160 bar and a condenser pressure of 0.045 bar. The turbine has an inlet steam temperature of 575°C, and has an isentropic efficiency of 90.5%. The pump has an isentropic efficiency of 88%. Hence, determine Show the cycle on a T-s diagram in relation to the saturation curves and clearly label all the principal points starting from the exit of the condenser. Sketch...
1. Ina Rankine cycle, steam leaves the boiler at 3.5 MPa 350oC. The condenser pressure is 10 kPa Determine the cycle efficiency. 150 points)
A steam power plant is based on the Rankine cycle with reheat (refer to the figure below). Steam is produced by the boiler/superheater (H-1) at 100 bar and 600 C at a rate of 2.5 kgs. This is expanded to 10 bar in the turbine T-1 and then reheated to 600 °C in heater H-2. The steam is then expanded in turbine T-2 to a pressure of 0.1 bar. The steam is then condensed in condenser (C-1) which operates at...
Question 5 1.5/3 points In a Rankine cycle, steam leaves the boiler and enters the ideal turbine at 6.9 MPala) as a saturated vapor. Condenser pressure is 6.9 kPaſa). The specific enthalpy of the subcooled condensate/feedwater at the discharge of the feedwater pump (h) is 166.36 kJ/kg. Identify the specific enthalpy (in kJ/kg) of the steam entering the turbine. 166.36 Calculate the quality (in %) of steam-water mixture leaving the turbine. Calculate the specific enthalpy (in kJ/kg) of the steam...
Tor steam power prants 4 marks D) A steam power plant is to be designed using the Rankine cycle with superheat. The steam must enter; the turbine at pressure (P) and temperature (T), and the turbine steam exit pressure must be 0.05 bars. In order to produce 12 MW, a steam mass floW rate of 8.91 kg/s is to be used and the dryness fraction at turbine exit must be 0.9. Assuming the Rankine cycle to be ideal and neglecting...
P8-29 A closed feedwater heater is used in a Rankine cycle Steam leaves the boiler at 20 MPa, 600°C. Between the high and low-pressure turbines, steam at 1 MPa is extracted and delivered to the closed feedwater heater. Feedwater exits the feedwater heater at 20 MPa and the saturation temperature of the 1-MPa steam; saturated liquid condensate is fed through a steam trap back to the condenser. Steam from the second- stage turbine enters the condenser at 10 kPa, and...
(15 pts.) In an ideal Rankine cycle that uses water as the working fluid. Superheated steam exits the boiler at 4 MPa and 600°C with a mass flow rate of 8 kg/s. The steam leaves the turbine at a pressure of 100 kPa. (a) Sketch the cycle on a T-s diagram (6) Determine the power output of the turbine (c) Determine the rate of heat loss from the condenser (d) The required pump power (e) The rate of heat addition...
(1) Q.5 (a) A power station using a Superheated Rankine cycle operates with a boiler pressure of 160 bar and a condenser pressure of 0.045 bar. The turbine has an inlet steam temperature of 575°C, and has an isentropic efficiency of 90.5%. The pump has an isentropic efficiency of 88%. Hence, determine Show the cycle on a T-s diagram in relation to the saturation curves and clearly label all the principal points starting from the exit of the condenser. Sketch...
Most questions answered within 3 hours.
-
Which of the following are common negotiation outcome
mistakes?
a. Leave money on the table b....
asked 4 minutes ago -
Propose an efficient synthesis of 2-Bromo-5-nitrotoluene from
benzene. Hint: 3 steps. Consider directing effects of substituents....
asked 10 minutes ago -
Convert the following quantities:
a) 0.819 atm to torr b) 512 mmHg to bar c) 11.2...
asked 29 minutes ago -
C ++ Implement cat command
The purpose of this assignment is to provide practice using the...
asked 32 minutes ago -
we
convert sugars into another form of stored potential energy. This
is called?
asked 1 hour ago -
The manufacturers of Oriental Spice Sauce are concerned that the
sodium levels in their product vary...
asked 1 hour ago -
PLEASE DON'T ANSWER IF YOU CAN'T ANSWER ALL OF THE QUESTIONS. I
DESPERATELY NEED HELP
Consider...
asked 1 hour ago -
DO NOT ANSWER IF YOU ARE UNSKILLED IN THIS AREA! TYPE OR WRITE
EACH ANSWER CLEARLY!!...
asked 1 hour ago -
how many moles of sodium are there in 3.41 moles of the
following compounds
NaCl
Na2SO4...
asked 1 hour ago -
1.1: Draw a position vs. time graph for a sprinter
running a 100 m dash. Label...
asked 1 hour ago -
A uniform electric field exists in a region between two
oppositely charged plates. An electron is...
asked 1 hour ago -
The energy levels of a quantum mechanical system are given by
the equation: En = -hfo/√n^2+9....
asked 2 hours ago